skip to main content

Changing CV joints

19 years ago

1997 Ford Escort sedan, 4 door.

How hard is it to change the CV joints.

How do I even inspect them to make sure that is the problem.

What is involved in changing them.

I can feel a bump-bump-bump-bump.... thru the steering wheel.

It can also be felt sitting in the passenger seat.

I inspected the tire on that side, and found a knot.

When I changed the tire, I found the tire was coming apart.

Changing the tire helped for a while, but the problem returned.

I'm thinking at the very least it is gonna need 2 new tires

and an alignment. And I think possibly CV joints.

20 years ago I wouldn't have had a problem tackling this job.

But now I want to know should I do it or have it done.

If I have to do it I'll get a Hayne's manual for it.

If it's not too involved to do it I will do it myself.

Or if it is cheap to have done I'll have it done.

I just need to know what I'm facing here.

Thanks.

Pooh Bear

Sort by:Oldest

Comments (2)

kalining
19 years ago
First of all. C.V.'s don't go Bump,bump,bump. Tires do.
C.V's will click on hard corners on acceleration. that is the out board joints. Inboard joints viberate on straight
acceleration. Don't even waste your time untill you find out what is what. Second. your wasting your money changing the C.V.'s, Change the entire axil. If you don't know how to take the CV apart and put it together properly you are
doomed. Do you know how to put the boots back on with a full grease load and burp them ? you are supposed to put on a new axil nut too, do you have one ? Some axils
fit so tight on the spindel hub they have to be pushed off
and pulled on. If you don't have 10 hours and a sh*#t load
of tools send it out if you need C.V.'s I dought you do.
Pooh Bear
Original Author
19 years ago
Sounds reasonable to me. That's why I asked here first.
I intend to get it looked at when I get new tires
and a wheel alignment. That may fix the problem.
If not I guess it goes to get fixed.

Last car I did any major work on was something from
the late 70's or early 80's. Easier to send it to the shop now.

Thanks.

Pooh Bear
Related Discussions
kohler cv12.5s-1270 small engine
Q
Comments (7)
Along with the other guidance given, you should replace the fuel line if it is original when you clean the carb. The other basics would be to ensure the vent in the fuel cap is open. Generally, you need good flow down to the carb. Yours has no fuel pump- it relies on gravity. Ignition coils on these do fail, and some times the cd in the coil that times the spark will tell it to fire at the wrong time and still have good spark. Normally starts as a hot stall though. To confirm, spray carb cleaner down the airhorn as you crank it- like a starting fluid. If it runs on that, then you're back to the fuel system. The battery ground cable on yours I think is attached to an engine mounting bolt on the RH side. I've had a couple give me fits as they didn't have a good ground at the frame anymore. If yours has a fuel solenoid below the carb, it needs- I think 10+ volts while cranking and a good ground to function. these plungers also get sticky from sitting.
...See More
kohler cv15s
Q
Comments (1)
John Deere has electronic fuel modules. One of mine went on my 345 and I had the same problem. Dealer replaced and works fine
...See More
Craftsman/Kohler (CV22) won't start
Q
Comments (7)
What's the 917.xxxxxx number? Craftsman schematics can vary, so being able to look at the correct schematic is nearly priceless. A "typical" Craftsman cranking circuit utilizes a WHITE wire from the key switch S terminal, through the brake/clutch swith and then the PTO/attachment switch to the starter solenoid. You can disconnect the latter 2 switches (1 at a time) and jumper the White Wires together, to bypass that switch for troubleshooting. You might also try jumping 12V direct to the small terminal on the starter solenoid. The engine should crank. You are pushing in the clutch pedal???
...See More
Kohler CV15S problem
Q
Comments (2)
I would when it stalls out see if it getting a nice blue spark? (if no spark or a yellow spark it may indeed be the coil) if it has a pretty spark I would squirt some carb cleaner down the carb and see if it will run off the carb cleaner. If so I would say you need to remove the carb. bowl on the carb and clean out the gum or find particles I would also try to clean the passages in the carb. IF that fixes it I would do a total fuel system clean up. Remove the gas tank and clean it out. replace all the fuel hoses and filter and run some gas treatment with a couple of tanks of gas that way you shouldn't have any fuel related problems for a few years. alot of people have reported here having good luck with sea foam.
...See More

Related Stories

LIFE Stop the Toy Takeover by Changing the Way You Think

By Apartment 46 for the Home

Make over your approach and get gift givers onboard with your decluttering efforts by providing meaningful toy alternatives

MOST POPULAR 6 Kitchen Flooring Materials to Boost Your Cooking Comfort

By Jennifer Ott Design

Give your joints a break while you're standing at the stove, with these resilient and beautiful materials for kitchen floors

INSIDE HOUZZ How to Create and Use Ideabooks

See how to gather inspiration, share it with others and put your design dreams on the path to reality

REMODELING GUIDES Tongue and Groove Wall Paneling Joins the Comeback Club

By Rachel Grace

Try this smooth architectural move to give your walls a streamlined appearance that conveys quality

WINDOWS Contractor Tips: How to Choose and Install Windows

By Buckminster Green LLC

5 factors to consider when picking and placing windows throughout your home

DESIGN DICTIONARY Shiplap

Overlapping boards allow for expansion on a home's exterior in moderate climates

DESIGN DICTIONARY Tongue and Groove

Tongue-and-groove wall and ceiling panels fit together to create flat surface with horizontal or vertical seams

ARCHITECTURE Design Workshop: The Art of Joining Materials

By Eric Reinholdt, Architect

Watch for carefully crafted meeting points in a home's building materials — they're among the hallmarks of great architecture

KITCHEN DESIGN The Future of Backsplashes

Grout is out. Continuous sheets of glass, stone, metal and porcelain are saving cleaning time and offering more looks than ever

DESIGN DETAILS Design Workshop: The Modern Wall Base, 4 Ways

By Eric Reinholdt, Architect

Do you really need baseboards? Contemporary design provides minimalist alternatives to the common intersection of floor and wall

Sponsored