skip to main content

Craftsman riding mower problem

9 years ago

I have a model no. 917.271022 riding mower with a kohler 15.5 engine. My problem started several months ago when it would not restart, if I shut it off while it was hot. After it set awhile and cooled off it would restart. Now it might not start cold and it might start and run an unknown distance. Some times it will just die, like you turned the switch off. Then when you shut it off, it will not restart. Even if you only run from the shed up to the garage, about 50 feet. I have changed the gas. Changed the fuel filter. Changed the plug. Cleaned the air breather. Changed the gas line. Could this be a problem with a safety switch or with the ignition and if so, how do I check for this? Thanks.

Sort by:Oldest

Comments (8)

mownie
9 years ago
In your opening post, you don't mention whether you have actually checked to see if the engine is still producing spark when it will not run.
Check for spark when it will not run and post back with that.
Once it is known whether the problem is ignition related, or fuel related.......we can go into diagnosis of either.
bill_kapaun
9 years ago
A bad or misadjusted seat switch on your SPECIFIC tractor can cause both the spark to be killed and the carb fuel solenoid to shut off.
Kind of a double whammy.

Make sure the seat switch is fully plugged in and the plunger has proper travel.
Related Discussions
Craftsman Riding Mower - Slowing Down
Q
Comments (2)
Your tractor has a hydrostatic transmission. While the drive belt could be the cause of your problems, I tend to doubt. However, since it's relatively cheap, I'd change it first and then proceed to more complex repairs. In all probability, the hydro is beginning to fail. Have you consistently kept the transmission cooling fan and fins clean of debris? Overheating is the kiss of death for small consumer hydros. Have you been towing or used any ground engaging attachments? As for the brake, it is adjustable, even though the owners manual from Sears tells you to have it serviced. The brake is on the right side of the transaxle, just below the cooling fan. You can get access by jacking the tractor up, and removing the right side wheel. The brake consists of a small wheel or rotor mounted to a stub shaft. A moveable brake arm connected to pedal linkage cams against two pins which in turn push the brake pucks against the rotor. To adjust, there is a castellated nut mounted on a stud of the brake housing. Remove the cotter pin and turn the nut clockwise to take up some of the slack. Dry fit the wheel and let it down to the ground to check braking action. Tractor should roll easily with no brake (and with freewheel or bypass disengaged), yet when brake is applied should cause wheels to lock up and skid. You may have to repeat several times to get it right. Then replace cotter pin on castellated nut and permanently fit the wheel with the appropriate washers and snap rings. Make sure you're not too tight, causing brake to drag. This will cause premature wear, reduce power and performance to rear wheels, and create a possibly damaging load on the hydro.
...See More
Craftsman LT2000 Riding lawn mower engine won't crank
Q
Comments (5)
Thanks for the response. It's definitely a Briggs engine. Or let me put it this way, there's a big 'ol Briggs and Stratton stamp on it. The model # is 31G77. I believe that's right. Good point. Getting a voltage reading is not a true indicator of whether or not the battery is good. It wasn't smoking, only when it conked out. It was laboring, laboring, laboring, then it conked out and threw out a puff of smoke. The reason why I'm GUESSING the engine is a little sieged is because when I turn the key, it appears I have good power going toward the cranking process (you can hear and feel that jolt of energy), yet the engine "stops" it. It's almost as though there's a heavy break on the engine. When I try and spin the engine from the top by hand, it won't budge. Then again, I have no idea if you normally can spin it by hand because I've never tried to do that! Sorry for being such a newbie. From the little research that I've seen taking the spark plug out and putting penetrating oil down it, waiting an hour then trying to manually move the pistons by hand as a *possible* solution. Again, this is assuming I'm right and the engine's seized.
...See More
craftsman riding mower gas fumes
Q
Comments (3)
Keep a roll of masking tape handy, and when you shut it off, place a piece of masking tape over the hole. Peel it off next time you start it. Problem solved. And yes, gas fumes will seep out of that hole, possibly from heat from running the engine. Only way it could give trouble, is if the machine is parked in an indoor heated garage, with an ignition source nearby.
...See More
Craftsman riding mower deck issues
Q
Comments (5)
My best advise is to use the OEM parts and watch the tightening of top nut. Me, I can zip them on w/ an impact all day and be fine. If they are over tightened typically the top bearing will fail and it may hog the pulley out. If they are under tightened- they will eventually chew out the spline. Auto parts stores will have loaner torque wrenches or a basic beam style wrench is available for cheap. You are looking for about 60 foot pounds.
...See More
tomplum
9 years ago
Sounds like a coil to me. Though on these your fuel supply must be set up properly. 2505007s is the proper fuel filter and ideally should be used as too big of bodied filter or excessive fuel line can be problematic. Fuel cap vent hole open etc.
for2baoke
Original Author
9 years ago
Thanks for the information. Turned out to be the coil, aka- ignition module. When it did start, I carried an extra plug, then when it died I pulled the plug wire. Inserted the extra plug and grounded it. No spark. Works great now, though. Thanks again.
vet1968
9 years ago
I have a craftsman lawn tractor model 917.27681. It quit on me yesterday after spitting and a sputtering for a while. So today I invest in a new spark plug,fuel filter,air filter, oil, filter and new oil change. I put in the recommend amount of oil 56 oz. So I try starting it again, it did start but with a lot of smoke spewing from the the front, and lots of oil shooting out also. I checked dip stick and the oil showed to the the top. I drain oil until dip stick shows full. Now it won't start at all and is still shooting oil out from the front.
bill_kapaun
9 years ago
You're missing a digit on the model number. Should be 917.276xxxx most likely.

Did you drain the old oil first?

Inspect the air cleaner element to see if it's "oiled up".
vet1968
9 years ago
I may have had a senior moment in changing the oil etc. yesterday. So today I made sure I emptied old oil etc. But it still does not start. On the flip side it is not spewing oil and the air cleaner has no oil. What do I do now?
The model # I posted is all I have on my operator manual .
bill_kapaun
9 years ago
The full model# is probably under the seat.

I'd remove the spark plug.
Ground the lead and crank the engine over for 5-10 seconds to "blow" any residual oil out of the cylinder.

You might have to wipe any excess oil off the business end of the spark plug if needed.

Related Stories

REMODELING GUIDES Houzz Tour: Turning a ’50s Ranch Into a Craftsman Bungalow

With a new second story and remodeled rooms, this Maryland home has plenty of space for family and friends

LANDSCAPE DESIGN Get Along With Less Lawn — Ideas to Save Water and Effort

By Jocelyn H. Chilvers

Ditch the mower and lower your water bill while creating a feast for the eyes with diverse plantings and gathering places

DIY PROJECTS Make Your Own Barn-Style Door — in Any Size You Need

By No. 29 Design

Low ceilings or odd-size doorways are no problem when you fashion a barn door from exterior siding and a closet track

OUTBUILDINGS A Kentucky Garden Shed With a Planted Roof

By Becky Harris

Sedums help prevent runoff and add a green touch to this charming backyard building

REMODELING GUIDES Original Home Details: What to Keep, What to Cast Off

By Laura Gaskill

Renovate an older home without regrets with this insight on the details worth preserving

TINY HOUSES Houzz Tour: A Custom-Made Tiny House for Skiing and Hiking

By Mitchell Parker

Ethan Waldman quit his job, left his large house and spent $42,000 to build a 200-square-foot home that costs him $100 a month to live in

LIFE Houzz Call: Where (and What) Are You Reading This Summer?

By Stacy Briscoe

Whether you favor contemporary, classic or beach reads, do the long and lazy days of summer bring out the lit lover in you?

SMALL SPACES Life Lessons From 10 Years of Living in 84 Square Feet

By Mitchell Parker

Dee Williams was looking for a richer life. She found it by moving into a very tiny house

KITCHEN WORKBOOK 8 Elements of Classic Kitchen Style

By KitchenLab Interiors

For this timeless style, go with white or cream cabinetry, simple architectural details and high-quality materials

LANDSCAPE DESIGN Is It Time to Consider Fake Grass?

By J. Peterson Garden Design

With more realistic-looking options than ever, synthetic turf can be a boon. Find the benefits and an installation how-to here

Sponsored

More Discussions

Mower Blade rotation

1