polyethylene pipe for sprinkler system

16 years ago

I have read a lot on this forum about creating/installing a lawn sprinkler system. The "Sprinkler" discussion that has been going on for a couple of years has some great information. There is so much detail that I am considering it for my own lawn. I have been shopping around to see what I need and where I can buy it. The one thing I have not been able to locate is the polyethylene pipe. I can find 1/2 inch polyethylene pipe for drip irrigation, but nothing for a lawn sprinkler system. In one discussion Morpheusa said he used "Goodyear high-density polyethylene (is that spelled right? Well, close enough) 5/8" four-season line capable of taking burst pressures of 1500 PSI". Does any know where I can find something like this? I have checked the local Lowe's store with no success. Any ideas?

Thanks,

mynextlawn

Sort by:Oldest

Comments (10)

turf_toes
16 years ago
Home Depot carries it in the plumbing section. Just about any plumbing supply store will carry it too.
mynextlawn
Original Author
16 years ago
Thanks turf toes. I got so caught up in the fact it was for a lawn irrigation system that I couldn't think past the garden center.
Related Discussions
Sprinkler system pipe repair
Q
Comments (2)
OK, the solution is tricky to do the first time but you can handle it if your very careful and a bit lucky. Dig a hole away from the valve about 12-18" long and about 2"-3" deeper than the pipe. Exposing the pipe all around so you can cut it off. Cut off the pipe as close to the bushing as you can without cutting into the bushing. Cut carefully. Cut off the pipe a few inches past the break. When you have this done you will see the pipe inside the bushing. Take a hacksaw blade out of your hacksaw and carefully cut through the pipe BUT not into the bushing. Be very careful. Move over inside the pipe about 1/4" and make another cut. Take a hammer and a very thin flat screw driver and very carefully tap the screw driver between the pipe and the bushing. Go slow and DONT hit hard. Angle the screw driver slightly toward the middle of the pipe so your applying most of your tapping to the pipe and not the bushing. If all goes well you will pop out a bit of the pipe in a grove 1/4" wide. Now carefully work the rest of the pipe out by tapping the screw driver between the pipe and the bushing working around the pipe. Often the pipe will pop out in one or 2 larger pieces. Be sure to get all small bits out. Repair the pipe/bushing with a bit extra glue and primer and it should be as good as new. If at any point the bushing cracks/splits you will have to replace the whole valve. Good luck, Tom
...See More
air in pipes after lawn sprinkler runs
Q
Comments (2)
When I purchased my home, (built in 1991), I quickly discovered that when the sprinklers were used they would suck all the water out of my pipes and I would get air through every faucet. I installed a brass check valve in the main line near the sprinkler pump. Now I never lose house water, but I also have NO pressure when they are on, so I must water at 4AM. I will not go the expense of a tank to maintain pressure.
...See More
Break in sprinkler system pipe
Q
Comments (2)
It's really an easy repair. Probably a 10 min. repair max for a professional once it's dug up. Possibly 1 hr. for the layperson. It will probably take you longer to hook up the fuuny pipe than it will to make the PVC repair! Parts required: 1x1x1/2" SST Tee 1x3/4" SS Reducer bushing 3/4" SS Ell 3/4" SS Coupling 3/4" pipe Cut the 1" pipe next to the tee and glue new tee w/ RB. Put a short piece of 3/4" into RB to the length of the 3/4" pipe that is perpendicular, or on the right in the bottom photo. Cut the existing 3/4" pipe back a bit to the right on the bottom photo. Maybe 6" or so. Glue the 3/4" coupling onto the existing pipe and then glue a piece of 3/4" into the coupling to extend it to where the ell will go. Cut the 3/4" to length for the ell and dry fit to make sure the lengths are correct. If so, glue the ell onto the 3/4" on the right of the bottom photo FIRST, the pull the 3/4" w/ the ell back and glue in into the tee w/ the small piece of 3/4" pipe glued into it SECOND. Reconnect the funny pipe to the head and you're basically finished. It's important to do this repair IN THIS ORDER or it could become a real PITA. Good luck! All Wet Texas Licensed Irrigator #1897 since 1984
...See More
Converting existing sprinkler system to pvc pipes
Q
Comments (0)
I have an existing sprinkler system on the raised vegetable bed that is not efficient. I want to convert it into a pvc system using risers to replace the sprinkler heads. I tried once to replace the sprinkler heads with the adjustable manifold, but the connectors to the pipes kept breaking off. Anyone tried this?
...See More
biglumber
16 years ago
Irrigation distributors will help you also. They have some great stuff you can't get at the box stores. One I have frequented is Ewing. Don't know if they are in your area but look them up.

Peace
grass_man
16 years ago
I get confused when I'm at the plumbing section of Lowes/HomeDepot with all of the different connectors there. For polyethelyene pipe what connectors do you use? I'm thinking that it is the barbed ones with a clamp (no glue).
I'm also half way into a homemade lawn sprinkler system. I know I will not be going below my frostline in Northwest Pennsylvania. I am hoping that if I get my lines drained out they will last atleast 2-3 years without leaks. Maybe longer if I get lucky.
turf_toes
16 years ago
1) Barbed connectors.

2) rent an air compressor from Home Depot for the day (cost: $25). You'll need to get the appropriate connectors to hook up from the compressor to the irrigation system.
grass_man
16 years ago
Thanks Turf-
My Dad has a largish compressor with a decent size tank. I am also thinking about adding an in line drain. I will only have one zone buried with 2 or 3 Hunter PGP heads. There is a slight grade over that area. I plan on installing a lateral line drain at the low point. (draining to into a french pit - and my soil is on the sandy side). These drains are closed with a psi >5, when the pressure drops they drain slowly. Here is a link to the drain I have. http://www.sprinkler.com/buy/item/line_drains/4311

Just curious - How deep did you get your pipe and how is it holding up? This question is for Turf or anyone else who made a custon underground system. I think I will only get the pipe 6-8 inches deep.
turf_toes
16 years ago
Well, a good portion of the yard was done with a trencher and I dug down 18 inches with that.

But other zones were dug by hand and are as shallow as 8-inches.

They all have survived their first winter just fine. As long as you blow the pipe out at the end of the season, you should be fine.
grass_man
16 years ago
OK - I'm back from a local big box store. I have 100' of black PE pipe rated to 160 psi. The guy in the plumbing section suggested to double clamp over the long barbed connectors. He also said this was reccomended as a conduit for well water. As best I can tell the High Density PE pipe (PAX brand) is very thick walled and uses a different connector with crimping tool.

I'll dig as deep as I can manage and possibly add some sand around the pipe in the bottom of the trench. Thanks again for the advice.
blip01
16 years ago
What size pipe did you buy? I wouldn't go smaller than 3/4".

My pipe is buried anywhere from 4-8" and was fine over the winter. I blow the system out with a small 6 gallon compressor. Works fine but takes a while.

I did not double clamp any of my connections. It's been a while since I bought those clamps, but I seem to remember them being almost $1 a piece. They'll add up pretty quick. I think one is fine. just use a ratchet to tighten the screw, not a screwdriver.
grass_man
16 years ago
Thanks blip-

I have 3/4" pipe. I found a bag of 10 clamps for $5.50. If I have enough to double clamp I am of the theory... if some is good more ia always better. I am sure one is fine.

If you noticed my other post yesterday "watering restrictions on a new lawn" I can't use my new system till maybe Oct 1st. I may sneak in 10 min a day at 4 AM.

It's nice to hear that yours and Turf's systems wintered over. Thanks for the input.

polyethylene pipe for sprinkler system

Comments (10)

turf_toes

mynextlawn
Original Author

Related Discussions

biglumber

grass_man

turf_toes

grass_man

turf_toes

grass_man

blip01

grass_man

COMPANY

BUSINESS SERVICES

GET HELP

CONNECT WITH US

polyethylene pipe for sprinkler system

Comments (10)

mynextlawnOriginal Author

Related Discussions

COMPANY

BUSINESS SERVICES

GET HELP

CONNECT WITH US

mynextlawn
Original Author