Oh! They look just like the giant round yews I used to have on the corners of my house. One yew in the yard was removed after we moved in by my very useful DH and I hemmed and hawed and thought about what to do with the others since I didn't want to see DH destroy his back. Well, I finally decided that I didn't want huge bare spots next to the house and have to put something else there anyway. So I went with the major trimming and I really like the result. HERE'S WHAT I DID: I would NOT recommend cutting them back to 2 feet even though eventually they will grow back. The trimming can be done in stages so you are not left with a bare stump. 1) You can cut back the bush hard all over as far as the green goes to leave some green showing. I did this first. Yours look much too tall like mine were. 2) Then, if you look inside the yews, you can see that there is basically a trunk with radiating branches and the green is mostly on the ends of the branches. What I did was to trim off all the lower radiating branches and leave the top of the bush green. The result will be a vase shaped bush. I wanted to make mine narrower to keep off the house siding and because they were blocking the path. The trunk and branches are actually quite attractive and the top can be rounded or shaped naturally or done like topiary if you want. This left a lot of room underneath the bush where I can plant bulbs or anything else. The yew roots don't seem like they are too thick or shallow for other plants. This will let you keep the shrubs, make them smaller, trim them away from the house, and plant more plants in front of them. If you would like a photo, email me and I'll see if I can figure it out. I just dropped in on this forum for a minute, but had to respond. Susan

these are the steps as listed on ehow Share Your Printer in Windows Step1 Install the printer. Set up the printer as normal on a machine that is already connected to the wireless network. Connect all necessary cables and install all necessary drivers. Step2 Open the printers and faxes folder. Click "Start," then "Control Panel," then "Printers and Other Hardware" and then "Printers and Faxes." Step3 Share your printer. Find the icon for the printer you just installed. Click the icon once and then select SHARE THIS PRINTER in the tasks pane on the left. Now, right click the icon, select properties and go to the SHARING tab. Click "Share Name," and then click "Okay." Step4 Connect to the printer. On the other computers within the network, open the control panel and click "Printers and Other Hardware." Select "Add a Printer." Step5 Select "Printer Connection." When prompted, select this option instead of the local printer. Find and select the printer you just installed and select it. Step6 Print as normal. Next time you print a page, send it to your networked printer. (you may need to reboot both computers after setup) This is also a good tutorial Beginners Guides: Printer Sharing on a Home Network you should also check to see if you have all the computers set up with the same workgroup name. "Workgroup name: This is the name of your network if you like. By default Windows XP will call your workgroup MSHOME, but you can change this as long as all the PCs on your network have the same workgroup name. (To see the computers in your network, click My Computer and choose Network Places from the bar on the left side. From there click View Workgroup Computers.)" (Control Panel > Performance & Maintenance > See basic information about your computer. From there click on Computer Name. Your workgroup is displayed.)

I'm in San Diego county near the beach. The supply is low and the demand is still fairly high. Many homes are going for well above asking price and above the appraised value. The area is extremely eclectic and subject to a lot of "emotional buying" and few of the comps at any time are actual comps. Buyers are bringing cash to make up the difference and driving prices up. For the next buyers these homes will be the comps and the next appraisals will be higher. Thats how it works.

Thanks - the shed would not be for the trash cans, plan would be to redo the fencing around the cans for concealment, and then do a shed for the other part so that I could lock up bicycles, tools, etc. That first pic that Larri posted is pretty much exactly what I'm looking for. Contractor is giving me about a $3000 quote to do something like that for that space. A bit more than I had in mind, but thinking about it. Ultimately yes, I would like an enclosed garage. However, that's a much bigger and more expensive job. Also, the space is plenty big for a carport, but as a garage it would actually be on the smaller side. My truck barely fits in the carport, I think with a garage door I'd find that it didn't fit at all.