Funny that you guys started to discuss this just when I am about to start this same project myself. Here are my findings. First off, if you plan of putting a counter on top of the new 3.8 cu ft FL, good luck, and have your pocket book ready. You see, the deepest "standard" counters are those for kitchens, at 25 1/8". Assuming that one leaves around 5" of clearance behind those newer FL machines for vents, air circulation, heat, etc, then you are looking at about 30"-35" of depth, depending on how flush you want the counter to come to the front of the machine. Having said that, there are 3 prices for laminate counters in the stores (like Home Depot). The counters you see in the store in stock are the cheapest, and will cost around $10 li ft. If you need to pick a finish that matches say the sink counter top in your bathroom where the machines are also located, then that is considered a custom order, even if it is a standard depth. This will easily double the price to $20 li ft. Now if you want to order a non-standard depth so that it goes from the back of the wall to the front of your new FL, then you are looking at $35-$50 li ft, depending on type of finish like rounded vs sqaure front edge, back ledge or no ledge, etc... Keep this in mind when shopping for a counter top. I would like my counter to cover the machines completely, so I might have to bite the bullet and order the more expensive counter top.... Again, I am talking about a laminate counter top, no fancy materials here.... I am from Canada, and here is what the local Home Depot quoted me in Canadian dollars for the 3 options.. 1) In-Store counter (limited finishes) 25 1/8" (standard depth) X 6 feet = $68 CAD Custom order counter (you choose the finish) 25 1/8" (standard depth) X 6 feet = $132 - $150 CAD 30 Csutom order counter (you choose the finish) 30-35" (non standard depth) X 6 feet = $222 CAD I believe the last option of non-standard depth only allows for a square front edge finish. If you want a rounder edge in front, like that found on your kitchen counter, the price jumps to $500 CAD, since the guy said that they have to charge for a full 4X8 sheet, and then cut the custom size from there, in order to get the rounded front edge... One other option you can do, which my brother did very nicely is lay down 2 sheets of plywood (for extra thickness), and tile the top and sides, looks really nice, but is a lot more work...

terry, do you mean LG Hi-Macs? Lomac is a drug. Hi-Macs is certainly comparable to Corian at a better price but it sure doesn't have more colors than Corian. Anyway, I'm sorry I can't help you with your sink concerns as I don't have a solid-surface counter. You may want to try searching "integrated sinks". One thing I know about SS sinks is that you need to run the hot water from the faucet before you pour hot liquids into the sink (like draining pasta) because the temperature shock can cause the sink to crack. Other than that, almost everything I've read about solid surface counters and integrated sinks is very positive. Nicole

If you're willing to glue it up, there's lumber out there--just not in Home Depot, usually, or your average "lumberyard"--those are usually selling to the building industry, and they don't want/need thick hardwoods. OK, I'm presuming you don't want to glue 2x4's together for this project...Frankly, the easiest thing to do is order a piece from one of the sites people've already given you. You don't have woodworking tools, right? To get a nice flat top, you're talking more than just sanding, you need to get 'em to be flat on the edges so's there's no gaps between the boards. Not that easy with just a sander, though you're not talking about that long a piece. Try looking for places that sell hardwood in your area--that'd be a better google term than lumberyard. Rocker sells some wood, but $$ (on the other hand, maybe you can get there by car?). I tend to buy nice wood at West Penn Hardwoods--have always liked what they send me. Anyhow, Home Depot etc tend to only have 1" (aka 3/4" in real life) thick hardwoods, when they have those. Suppose you could buy, say, 2" x 1" maple strips and glue together on end, but I wouldn't, that's just too much gluing! The Amazon piece--you do know maple's not the greatest for staining, right?

Here are a some pics and my dilemma. Keep in mind this is my old fridge...new one comes today! Here is how we ended up with this: I have never had an enclosed fridge so didn't think about the peninsula dying into panels or how deep panels were going to be. I "semi" designed the new footprint and took it to Lowe's where the KD took over. (yes---I know......) Bought Schuler plywood with maple fronts cabinets. Although the kitchen designer had the model number of the fridge we were buying, which is a full-size, she designed the kitchen with 24" deep panels. She knew I was trying to have the look of an enclosed fridge. Being that I've never had an enclosed fridge, it was something I just didn't think of until the install started. Evidently she put a counter-depth in the design program because the elevation sketches she gave me showed an enclosed fridge. "Luckily" the panels actually came in wrong and were cut at only 23" for some strange reason and the installer caught it right away when looking over everything. Otherwise he probably would have installed them and I would be stuck. So called Lowe's to reorder the panels and somehow in all this it suddenly dawned on me that a full size fridge was going to be deeper and require deeper panels. I thought "no problem! Yay I can order them at 30!" By this time the KD had quit her job due to the pandemic. The other KD didn't know what was going on so we called in the Schuler rep. She was the one who immediately told me that those 30" panels would be sticking out in front of the peninsula. She asked if we could move the peninsula forward since the other side is an overhang for seating, but we couldn't since it would bottleneck the entrance into the kitchen down to under 36" and getting rid of an existing bottleneck was one of the reasons for the re-design to start with. So we had a dilemma. We cannot go down to a counter depth fridge which was the other option. What I decided was to split the difference and order 27" refrigerator panels. The fridge without doors is 29.5" so I will have about 3" of the side of the fridge sticking out which I don't like, but while I want my kitchen to look beautiful, I value the functionality too. The old fridge that you see in the pic sticks out a total of 32" The new fridge will stick out 34 with doors but without handles (4.5" of that is doors that would stick out anyway) Here's the really complicated part....we will be installing decorative panels on the end of the fridge as we have them on all the cabinets. This is how you enter the kitchen and I don't want that big blank space there next to the peninsula. The panels should be installed with just 1/4" reveal. I posted a photo below of how the panels look that are already installed on the side of the pantry that adjoins to a 17" high window seat. Luckily those face the opposite way from the fridge panels so you will never see both at the same time. I also posted photos of us holding up panels on the side of the fridge (they are NOT the right size panels...we have to order those still---we just used these to look at the right edge as to how wide to make the panels.) Also keep in mind we can remove the quartz backsplash piece if that would look better. That was not originally planned...the panels were going to sit directly on top of the countertop. So do we order the panels with just the 1/4" reveal to match the panels in the rest of the kitchen? Or, as the Schuler rep recommended, order the panels so they are the same width with the countertop, leaving about 1 3/4" reveal on the right side, but then your eye follows the countertop all the way up. I asked the countertop templater guy if I should just lengthen the overhang on the kitchen side of the peninsula to 2.5" to bring it out to within 1/4" of the fridge panel but he said no....I'm now thinking I should have insisted on it. Especially since we have full overlay cabinets that already make the overlay look very small since the 1.5" planned overhang is measured from the box, not the front of the drawers. Note how small the overhang looks to the drawers. And then of course, they had templated for a 1.5" overhang and I only got 1.25" UGH! Every quarter inch there would have made the reveal on the side of the fridge less. Suggestions appreciated! I'm hoping that I will eventually make peace in my mind with this issue and won't notice it but it is driving me crazy right now. I think of all the things that screwed up just because of this one error by the KD that I didn't catch and I am beating myself up for it!