Oh, good. I think that is closer. The Rohl is 19.6 plus 1.5 overhang, plus .75 cabinet plus aproximately 2 inches to the faucet is 23.8 if you put it all the way against the front. I made a mock-up cabinet with a salt shaker as the handle at 21.75" and I am almost needing to lean to touch it. So I think I should switch to the Kohler Bakersfield and ask the fabricator to move it as forward as possible in the cabinet and the hole as far forward in the predrilled sink hole. I might even shave off some of the countertop overhang so that I don't have to lean. Do you have the eased edge and is yours the standard 1.5" overhang?

My Mom's apartment isn't completely wheelchair accessible, but it is designed with Seniors in mind. All the wall outlets are 2 feet from the floor instead of 1 foot. One doesn't need to bend over so far, and they can be reached from a wheelchair. I wouldn't have thought of it.

A lot depends on the sink. I don't feel it should be centered in the cabinet. I like sinks pulled forward in the cabinet as much as possible for two reasons. First, less leaning in and more comfortable use. Second, it leaves more space in back. But this is something the fabricator often decides automatically unless it is discussed in advance. And if the counter is stone it can require more delicate templating -- something to inquire about/discuss when they come to template. I have stainless counters so when he came to template I actually had the faucet on hand and we were able to hold it up and see where it should go. Then you can have your calculations at hand but make adjustments at the critical time. That's best case but not everyone can be there. Also, I don't assume counter over hang because it depends on the style, material and fabrication. Some counters have overhangs and some will be flush with the front of the cabinets -- though I don't feel that's most desirable -- and yet modern kitchens may have that. Another point to discuss. Again, with mine, the KD wanted more overhang than I did and I had her pull it back to 1/2-inch. So, what I'd do -- and maybe you've done this already -- is get the spec sheets for the sink you want and the spec sheets for each faucet you're considering. There was a similar thread by sparkling water where I posted those (link is below) and walked through key issues for each. You can see what you think. Measurement formula basically is drain center to inside edge of sink + additional width of exterior sink flange/clips+ setback 2-3" usually (but that depends) + half the diameter of the faucet. I don't worry about the back or the tile thickness unless I was going with very thick 3 dimensional tile or they are building out the wall for some reason. As a rule -- just a guideline -- there should be around 5+ inches in back but that can vary with how the sink is positioned. I pay attention to that as not all cabinets are made the same way. And the sink needs to rest on the frame, of course. If the spout is lined up with the drain (it needn't be dead center) splashing is usually eliminated. But, some faucets don't splash even if they aren't lined up. The deeper the sink, the less splashing unless the water hits something. Splashing also can be a function of the flow rate -- how many gallons per minute the faucet handles and how much water pressure a house has. In the other thread, there was a difference in that among the various faucets. Flow rate also is noted on the faucet spec sheet -- something to consider. This would not be as knotty if more showrooms had the faucets hooked up and functional. One look that way is worth hours of time!! After typing this, I started a thread to compile a smart list of showrooms across the country that offer working faucets. Here is a link that might be useful: sink/faucet thread This post was edited by rococogurl on Sun, May 19, 13 at 19:41

DivaMum, We're sort of the opposite of you! I got a great deal on our faucet at an online auction (through HD), and it was the first thing I purchased! Even before my cupboards. The finish on it doesn't quite match my Stainless sink (perhaps mine is more nickel?), but it is a Blanco rados gooseneck with pullout. I measured it, and the 'reach' from edge to edge is 9", so really not quite 8" extends into our 18 1/2" deep sink. As teedup said, I really wouldn't want it extending any less than that for filling up pots, rinsing dishes, etc. Here is a link to a variety of single handled Blanco faucets, I just googled, so I have no experience with this seller, the site just has good pics. Here is a link that might be useful: blanco single-handled faucets