Sheri: The Aluminet stretches in one direction only, so when you order it, make sure you have the fabric cut to stretch in the direction it will hang from top to bottom. When the sales rep from IGC (where I ordered mine) told me the vents would open under the fabric, I was a bit doubious, but she was right. The key is to mount the fabric without stretching it tightly. My husband was concerned that the corners of the vent windows might punch holes in the aluminet fabric and wrapped rags around them. So far, even with the vents opened full and pulling the fabric, no holes, but I'm looking for a more elegant solution. Fat, self adheseive foam bumpers come to mind. But I didn't suggest that you use the aluminet AS a screen, only that when it's draped over the ROOF vents, it serves as one, which I found ironic, because we made screens for the roof vents, that will soon serve as storm panels for winter, as we can use them to hold bubble wrap in place under the vents. For your intake vents, use standard screening material, in a frame. To screen the powered intake vents on my GH, we used white vinyl house trim materials to create a box frame, 5- 1/2" deep, to allow the vents to open out, then just made screens using the screen channels, corners & spline sold in any home center. The box is made of 1 x 6 vinyl trim board, (actually 3/4 X 5- 1/2) so the edge facing out is wide enough to accomodate the screen frame, that is mounted to the box face with screws. To give a surface to mount the box to the GH, we used vinyl brickmould. The box sits inside brickmould, attached with small screws. The brickmould was fitted tightly around and to the fan frame, sealed with silicone. Once we fiddled the design, they were pretty easy to make and give me the ability to both remove the screens for cleaning, and in late fall, when we seal up the GH for winter, we can seal the vents by placing insulation in the boxes, then use the screens to hold it in place. My inspiration was shadowboxes, which, when you look at them, are no more than a picture frame with a second frame inside of it that projects out, with another frame on it's face, to hold the glass. From the craft shop to the GH. LOL!

Try some oven cleaner. Let it sit on the stain for an hour. Then wipe off with a Mr. Clean Eraser Sponge. You can get them at Target, the grocery store, or WalMart.

I found the tax shelter in this posting when searching for a gift for my brother. He is a tax preparer and has everything. So I just had to share what I did for him. I took one of those woodcraft houses from Walmart- removed the two screws from the base. I cut a 1" block of wood that fit into the bottom of the house. I glued this block onto the base thus allowing the top of the house to be easily lifted off the base. I cut a 1/2" groove in the center of the block with the table saw so I could set a card of thumb tacks into it. This was hidden in the house until the top was lifted off. I wrote a poem for this & read it to him while my daughter did a Vanna White presentation of the house. Everyone got a good laugh out of this and I finally did a complete craft project! It's been a while. Hope you have as much fun with this as we did. Here's the poem: I drew your name for Christmas It's an honor, don't you know To get my brothers name for Christmas Ah! ashopping I will go. But then I started frettin After searching high and low Whatever will I get 'im (Twas wrong to worry so!) I went into an office shop Maybe something for your desk? I talked to the clerk a lot She tried to aid me in my quest. He could use a tax shelter Is what the lady said It seemed a bit off-kelter But there was nothing left instead. So here's your little shelter All painted so very nice The foundation has been mended The roofs' been polished thrice. The flowers are all blooming In the big pot by the door The bumblebees are buzzing And there's no sawdust on the floor. It seems to be the perfect place I do agree she's right It sure beats a plain old case And your tacks! They're finally safe at night!

Ok.. I ditched the idea of adding some additional sound proofing to this machine. The drum clearance is just not enough to get even 1/2" of foam or other material in there to deaden any sound without it rubbing on the drum.. Oh well..