When it comes to root health, pots with gas permeable walls carry the day. Terra cotta clay pots are better than plastic or vitrified clay pots and fabric pots are better than terra cotta clay. The reason is greater gas exchange through container walls and the fact that an increase in gas exchange comes with an increase in evaporative water loss, which can be a lifesaver when using water retentive media. There will still be a PWT in these pots, and for any given medium it will the same ht in a pot with rigid sides as in the fabric or air pots at container capacity. Container capacity is a measure of how much water the grow medium in a pot or container holds at the moment it has stopped draining after having been watered to the point of complete saturation. The ht of the PWT and how long it affects root function is usually key/critical in determining what opportunity a plant will have to realize as much of its genetic potential as possible (within the limiting effects of other cultural influences). The factor that most affects the ht of a PWT is the size of the particles from which the medium is made. So, reducing the duration of PWTs limitations increases the opportunity for plants to realize a greater measure of their genetic potential. But wait! There's a more important consideration. If you place your fabric containers directly on the ground/soil, from the perspective of hydrology it changes the fabric container to a raised bed; this, because water is free to move through the fabric between the grow medium and the earth, with the earth acting as a giant wick. This means, because of the increase in the force of adhesion in the mineral soil beneath the pot (due to a mineral soils much larger o/a surface area on a per volume basis), water in the soil will be pulled downward with enough source to overcome the capillarity holding it perched in the container. As long as you don't place the fabric container on coarse sand, peastone, or other large particles, the earth will likely pull all perched water from most media one is likely to use in a container. I've mentioned this and the fact that healing in your pots situating them directly on top of soil turns them into raised beds. the only caveat being it's essential that there is a 'soil bridge' so there is continuity of the soil column between the soil (earth) and the grow medium in the container, through the drain hole(s), so water doesn't have to jump an air gap to exit the container. This applies more to pots with rigid walls and is not a factor when discussing fabric containers. Al

Hi Al and others, I would appreciate advice on saving sick/dying Picea glauca, in pic.1, please. I bought it on post Xmas sale and it was ~50cm tall, looking healthy, with very bushy top. I repotted it without much root cleaning to keep most original soil with fungus, which I read Picea, like other pines, needs. I planted the rootball with old soil into gritty mix, mostly pine bark fines with seramice, with a bit of gravel, see in pic.2 very "gritty" indeed :); trunk is ~1/2" at the bottom). I used a biggish pot to let it grow freely for a year or two. I also cut the top to encourage lower branches growth but it never happened. Water it when the pot feels light, ~ weekly (it is early autumn here in Sydney) by bottom watering in a bucket, then drain well by keeping the pot at ~45 degrees for a while. Use diluted Nitrosol liquid plant food every two weeks. Keep it on sun for 2-3 hrs, then half shade. Despite all my care (or coz of it ? :), the picea never showed any new growth but started developing warning signs for last 2-3 weeks. Those few thin branches started dying. Their stem turns from brown to greyish-green and gets soggy before dying. See in pic 3&4, that branch in front which is dying now, with grey stem. Other branch died a few days ago. Only three normally looking branches are left. But I am afraid they are facing same fate. Anything I can do to rescue my future picea bonsai at all? Thanks and cheers, Sergey

Phals can be easy to grow, but they were not easy for me to grow in either bark or sphag. Bark does not retain moisture effectively enough to suit them. Sphag can hold too much water for too long, especially when it becomes compacted in the pot and air can not move through it. The most foolproof and beneficial potting method I have found for Phals is to use fine to medium-grade coconut husk chips in an ordinary clay pot or orchid pot, either glazed or unglazed with openings cut in it. A plain plastic or glazed pot is okay, but not as good for maintaining an ideal air-moisture balance as one that can breathe. In any case, it seems that the best shape for a Phal pot is more or less the shape of an African violet pot. Squatty rather than tall in relation to width, and just large enough so that the roots fit comfortably in it. CHC retains water well, but it also holds air. It provides an excellent environment for Phal roots, which need air, but do not want to dry out between waterings. If a Phal has lost some of its roots, either from smothering or dehydration, it can quickly grow new ones after being potted in CHC. The specific frequency of watering a Phal in this medium would depend on the light, temperature, relative humidity, and air movement where the orchid is kept. Under ordinary indoor conditions with fluorescent light, I water mine every 5 to 7 days, usually with an organic fertilizer each time.

Pull the siding and make a drip edge is about it.