Thanks to Phyllis_MN for clipping this old post and saving it from the cyberscrap heap... Rigid Wall Baggie-Udated Method posted by: monte on 02.25.2007 at 01:50 pm in Winter Sowing Forum As some of you know I like to tinker with "processes". This is an update on my previous posting on sowing in baggies. The original post is linked below if you want to reference it. Cardboard Supported Ziplock Bags Scrounged containers are a great way to reuse things that would wind up in the trash. But sometimes the "need for seed" exceeds our ability to gather enough containers to get the job done. This leads to, what some may believe, odd behavior. Late night or early morning trash raids are well understood here on the forum but the public at large may not get it. What to do? One option is to use common ziplock bags with an internal support made from corrugated cardboard. The cardboard form not only stiffens the bag but acts as a support to create some head room. Quick easy and effective. I think that for many of us this would be a very economical method of making many containers. If you want to precision sow you can easily insert dividers or use paper pots inside the bags. Materials Needed 1. Gallon Sized Ziplock Bags 2. Corrugated Cardboard 3. Hole Punch 4. Stapler Preparing the Cardboard 1. You will need to prepare strips of corrugated cardboard to form into cylinders to slip inside the ziplocks. I have found that a piece of cardboard 23 " wide and 5 ½" tall is the ideal size for a 1 gallon ziplock bag. You need to be sure that the "grain" or specifically, the corrugation of the cardboard runs vertically on the short axis of the piece. This ensures that it will easily form into a cylinder. After doing a number of these I found that after filling the bags with the soil it was sometimes more difficult than it needed to be to zip the bag shut. The tension also seemed to "squeeze" the cylindrical form into more of a football shape than I wanted. I shortened the height by ½" to 5" and this made it much easier to zip shut and it held a much rounder "open" form. 2. Tightly roll the cardboard to loosen it up a bit. This allows it to more easily form into a cylinder. Overlap the ends by about 1 ½ÂÂinches. Staple together to form your cylinder. Again it took doing a number of these but I found that it took considerable amount of hand strength to tightly roll the cardboard to make it more pliable and the resultant forms were not ideal cylinders. A lot of angular corners and such unless you rolled it very tightly. I thought that for someone with arthritic or carpal problems this would be a deal breaker. So I decided that I needed to "drag" the sections over some type of form to loosen them up. What I came up with was to grasp one end of the section with a pliers and, with a gloved hand, (paper cuts hurt) pull it over a something. After the first pass the cardboard is much more supple and the effort was considerably less than rolling. I usually make three or four passes flipping the section over each time. The piece then forms into and holds its cylindrical form very easily. Once you get a rhythm going you can rip thru a lot of pieces very quickly. Preparing The Bags 3. Take the hole punch and punch a few holes along the top and bottom edges. These are you drainage and vent holes. For efficiency I just fold the bag into quarters and make one punch at each end. The only change I made here was to eliminate the folding over bit. It was faster to just slip the edge of the bag into the hole punch without folding it. I worked out a pattern of five staggered punches along the bottom edge and three lineal punches under the zip. This created a grid of ten evenly distributed holes in the bottom for drainage and six at the top for venting. I processed thru a whole box of 80 bags in about 10 minutes. 4. Insert the cardboard cylinder into the bag. Once inserted it will hold the bag fully open. To insert the prepared cardboard sleeve I grasp it in what I call "pretzel fashion. I position the stapled section midpoint on the side as this seems to hold the ideal rounded form. Once inserted I tuck under the bottom corner points and slightly pull up on the sides of the bag to tighten up the form. 5. Fill with 3" of your favorite soil mix and sow seed. Once the forms are inserted I find it efficient to pre-fill a number of containers at one time. If I have found one downside to the baggies it is that the bottom tends to sag if you need to move them individually. So I decided to place them onto cheap aluminum cookie trays. Keeping them on a shallow tray supports the bottoms eliminating this issue. The pans are inexpensive (2 for $1 at one of my local dollar stores) and should easily be reused for many seasons without taking up much off season storage space. Each tray holds five containers. I also am going to scrounge or make myself a "pizza peel" to make handling the sown containers and pans less disruptive. Once I place a fixed amount of soil (in my case three scoops) in each baggie I tamp the surface down with a flat bottomed object. I am using an end cap from some irrigation pipe but anything will work. This tightens up the form somewhat and also makes it simpler to see where seed is being placed. After filling and tamping they are transferred onto a tray and I fold in the upper portions. Having all the units at the same height allows me to stack the trays up until I decide on what IÂm going to sow. One question that often comes up with Wintersowing is "how do you efficiently water hundreds of containers?" A very valid concern. I lost almost all my first Wintersowing efforts due to drowning or drying out. Natural watering from rain or snowmelt is a non issue as the baggie forms a natural concave catch basin and will drain thru. But as the season progresses additional watering becomes needed. Bottom watering is the clear favorite but that could entail moving lots of containers around. This brings up another benefit of placing the baggies onto trays. I put a couple of fairly large drainage holes along one edge positioned between two of the containers. These allow full drainage and can be temporarily taped over from the bottom with tabs of duct tape if you want to add water later in the season. A note on efficiency. One thing IÂm discovering with this baggie method is you can prepare quite a few containers and have them "Ready to Sow" in very little time if you break up the tasks assembly line fashion. Gather up and cut the cardboard in one session. Relax it for forming into cylinders in another and so on. I estimated that I could probably prep enough cardboard and baggies for a whole seasons worth of sowing in a couple of hours and just fill them with soil as needed. I filled and sowed twenty containers and had them set out in a 1 hour session. This is my favorite method so far. IÂm setting up some stair stringers with scavenged wire shelving on the side patio to lay the trays on. If I need to shade them at some point IÂll just set up the picnic table umbrellas. This is going to be a breeze.

Thanks Julia. I saw that one and the one from Rick to Ellie. But I really could have swore there was one that said "More Chicken Fat" I think I remember the post going for over a week with people adding photos. Maybe I'm just thinking wrong and the link you posted is the one I was looking at. Thanks Andrea

Don R, I absolutely cracked up with that thread you linked....and you started it. Big puckers.....now that is wonderfully descriptive. I can see it smooching up, like plants do on Plant Delights Nursery catalog covers. I'm including a link to a part of the PDN website where they might sell "ghosts of catalogs past".....incidentally, I save ALL their cat covers. Great humor, really neat art work for gardeners. Here is a link that might be useful: PDN Cat Covers etc.

Is this it? I did a search of your name and a bunch of stuff came up. Here is a link that might be useful: jeanteach