Are you talking about brushed chrome or nickel. They are two different finishes. Brushed nickel is more popular and easier to find things in. I don't think there is anything wrong with mixing finishes but I prefer to stay in the same color family. We did a mix of metals in our bathroom, chrome (Moen) in the shower, brushed nickel for lighting, towel bars and toilet paper holder. I found sink fixtures with the body in brushed nickel but they have a trim in chrome on them too. For the cabinets the handles I wanted to use only came in worn nickel. Our bathroom leans to the traditional side and the mixture still works beautifully.

Ajsmama: The door pics look really nice, with a smooth look. I learned from mostly Minwax literature and some forums that I'll need pre-stain treatment to solve the grain/absorption problem with woods like pine. Then I was just going to stain, and with a final coat of poly. I wasn't sure where sanding would come into the picture, probably just sanding off the dusts/specs that got trapped in the poly. I am not even sure what I can do with the raised grain with a water based paint/stain. The raised grain on the trim (after being painted with glossy latex paint) was just about impossible to sand down. I suppose it's not terrible being trims, but for doors that may just make enough difference to matter. I am using a 150 grit paper. I was thinking of using small foam rollers to apply the poly, if not the stain, for an even finish. However, that's just a thought in theory: in testing on sample drywall/wood blocks, smoothest finish with anything water based paint/finish could be achieved with those high density foam rollers, much more easily than brushes. Of course, these are the plans from someone who has no experience and learned from very scattered materials. I see here that there's a 4th step before coating with poly, to "use shellac as a sanding sealer". I'm not sure how that works, how to apply (I imagine coating and sanding, assuming shellac is a softer material than poly to sand down for a smoother finish?), or what exactly shellac is. I'm just that far off the curve here. :P Magnaverde: I just learned how oil based may achieve a superior finish. I asked around in the store and nobody could tell me the difference between oil and water based other than that water dries faster and doesn't smell. That made it an easy choice, as it is getting pretty cold here and opening window to vent VOC will be tough. Given that, I'm wondering now how difficult will it be to sand down the grain if I use water based stain/paint, to achieve a similar result to oil based paint/varnish/stain? Also if done properly (with pre-stain treament and all), is staining the pine with those grains acceptable, and in what color/finish? I suppose "naked door" with poly is nobody's cup of tea here. :) I'm not sure if a sketch of the room's dimensions will help visualizing the door better than a picture of one corner. Here it is: As you can see the apt has a very odd layout that cannot be salvaged easily. The door in question is the one to the top, next to the window/mock sofa. Most of the furniture are in maple/natural/pine color, as they were modular and simply carried over from the apartment rental days (new furniture may be in order). I haven't sketched up the trims though, but they are 4" base trims with 3.5" door casing, the largest I could get without going to the lumber yard for some much fancier versions. The trims and casing are painted in benjamin moore's "superwhite" in glossy finish. The front door (right hand side) at the end of the corridor is finished in white. The closet (center of the apt) has a bifold pine door that will be finished the same as the bathroom door. I'd appreciate any ideas/opinions with the door finish, again. I'm thankful of all the help here. This is so much more than I imagined I'd get in return to my question, which was originally thought to be as simple as a door knob finish. :) The question with the door had always been a bit nebulous to me, and it's just now began to clear up. Thanks guys.

Hi there. I haven't actually compared, but I am also mixing chrome finishes - Kohler and HansGrohe. From what I understand the benefit of chrome finish is that chrome is chrome across the board so you can mix and match. I hope that's true! I actually have my trim pieces here somewhere so if I have an chance I'll go out and compare them and report back.

Yes, it's the same thing. Chrome is by default "polished" by which is meant bright and shiny. It does not have to be. There is brushed chrome, matte chrome, etc., but it is almost always identified by the adjective qualifier. There is such a thing as highly polished chrome, which is chrome that has in fact been carefully polished, sometimes called mirror-like chrome. Take a look at aRestoration Hardware chrome faucet for an example.