I bottom water my tomato plants. I put one seed in each 16 oz. styrofome cups with holes in the bottom. I set them in the bottom of milk jugs that I cut the top off. I keep two cups in each with about one inch of water in them all the time. As for soil. I plant them in nothing but composted oak leaves. The leaves do stay a little yellow, but when they are planted in the ground they quickly green up. Click the link. Here is a photo of my tomatos ready to be planted in the ground. I planted them in bigger pots. Now I use smaller pots. Bigger pots are harder to plant out. I started these earlier. I grow my seedlings on the porch with a window to the south. Karyl Here is a link that might be useful: Tomatos ready to plant out.

I used to have that happen it would not recognize it till I unplugged then re-plugged the keyboard then it would find it and work, luckily I have a KVM switch on my desktop so it was easy to get to do do this, I love a wireless mouse but just can not get a good wireless keyboard that I find worth the effort so I use a wired one with virtually no problems, I mean it is on my desktop just how far will I be going with it anyway. Also make sure the receiver is not blocked or out of line from the unit.

I like the water hose on the joints test. There seems to be 2 leaks in glued joints. There does not seemto be enough room to cut and reglue pvc. I will check the valve thing tomorrow. Need to get the suction up because I can't get the water clear with low suction. Not enough suction to clear the water surface with pecan seed things. Nothing moving

Yes, pigpig - this inquiring mind sure wants to know too!! Dadoes - it's so cool you're still here. I haven't been around in a decade I suppose, but GardenWeb was THE BEST helping me redesign my kitchen and house. There are so many on here so generous of their so extensive knowledge. My appreciation is kind of boundless here. Anyway... pigpig - I'm in precisely the same situation. I have a HE4T that is probably 21 years old? It's not broken, but it will be, I think, too costly to replace. And my love for the thing is perhaps not quite as traceable to flawlessness but laced with a bit of Stockholm syndrome? Over the years I've refloated the solder on the motherboard I think 3x? And replaced the collar once and the shocks once and the water flow stuff. Now the shocks are bad again and the collar is also leaking (ie rusting the body, not unrelated to the shocks problem). Since I guess that means I have to replace all the shocks, even though they're just ~$50 ea, all told we're looking at ~$400 repairs. Which on a two-decades old machine.... the cost:benefit starts to tilt against. SO.... back to GW. Or, I dunno, ...howz this different now? ;) Thus: I am very curious about your LG choice. I was thinking of making the same. My HE4T IIRC definitely started with that "110..." serial number so it's really a washed-over Whirlpool. Do they still exist? Dadoes said "was"... implying maybe not. I know, located at the bottom of a hill, we have very heavy water pressure here. That sounds bad from the outset. We do have a slate floor so that might help but this sort of hammering does sound like a pia and I'm a little nervous to try it. That said I loooooove our FL machine. I have used this machine so many thousands of times, washed so many thousands of diapers and bedding - I feel practically spiritual about it. I feel guilty about retiring it. But part of that is because I don't want to take on a new set of problems. The hammer-thing sounds horrible and it will be really good to know if you've been able to preempt it or if there's any good way to anticipate who will/does have issues. We certainly have a complaint bias/denominator problem in here inasmuch as a few people have chimed in with "no issues" but, given the popularity of these machines it does seem possible the proportion of problem-households/machines is really quite small. But again, knowing whether you were able to stave problems off at the pass, would be super-helpful. Also, I'm in the market for suggestions... *****sigh*****. Please hop in if you have any. I gather there's at least one major-proponent of Mieles in here. But the machines are awfully pricey. And cost and availability all seem to be competing in a post-covid screwed-up-supply-chain atmosphere, so.... Fwiw we have a Miele speed oven which has been/was a GREAT product until... it had a problem. Zero human beings seem to know how to fix them (even around here, which is LA, not what I would consider a small market). And my pitiful attempts have been half-successful and wholly-annoying. Thus, I'm reluctant to buy another Miele. BTW - another mentioned purchasing via ABT in Chgo, which is where we got that Miele speed oven. I second enthusiasm for Abt's support. They have been nothing but wonderful, even if it's 2000K miles from this urban center. I'd buy an appliance from them via mail again. Love Abt. So, at last, my q: ¿How to replace a HE4T 1:1? lol. I want a front loader. I want high efficiency. I don't want to destroy the water pipes. I want large enough to wash a kind size blanket, but not quilt necessarily. That's expendable as a need, but it seems sizes are either small or gigantic anyway. The 4T is actually 3.8 cuft I think, which is medium-sized by today's standards. It's plenty big-enough for us and I'm not eager to replace it with *bigger*, however, it seems there's not really a choice about that. Thanks amazing GW'ers. This place will always be GardenWeb to me.... BTW - here's a link to reviews of the new whirlpools. Lots of the reviews are "incenitivized", fwiw. Kinda meh-sounding a little? Hard to tell....