I was thinking of the hutch idea as well. Put a pantry height at the opposite end from the oven and use the space between like a hutch. If you're into wine you could make this a wine bar or coffee area. As I thought about my own kitchen I realized I designed it with a landing area next to the oven and we NEVER use it like that LOL. We always open the oven and carry the hot stuff over to next to the sink or set on the cooktop for some reason. I guess it's just the natural traffic flow of the kitchen. So now the section next to my wall ovens is the beverage area when we have gatherings. I also like the idea someone mentioned for a laptop or charging area. You could hide some outlets up under the upper cabinets or do a couple of those pop up electrical outlets. This post was edited by bocron on Wed, Feb 5, 14 at 13:02

I don't know what you intend to do regarding backsplash height (that's the distance b/w the finished counter and the bottom of the upper cabinet and light rail), but here's what I usually tell people when they're considering the height for their backsplash. The standard is 18"...regardless of the reasons why, it's still the standard.. How this affects your kitchen.... Refrigerator and other tall cabinet heights...Because wall cabinets are meant to be mounted at a standard height, cabinet manufacturers take this into account when designing tall cabinets. Tall cabinets are designed to be the same height as the installed wall cabinets so the tops all line up. When you change the height a wall cabinet is installed at, it affects cabinet top alignments. With the refrigerator you can usually mount the upper cabinet a little lower OR order a shorter upper cabinet, but be sure you don't make the alcove any shorter than 72" tall b/c newer refrigerators are 70" to 72" tall (and seem to get taller each year!) With other tall cabinets like oven cabinets and pantry cabinets, they're a standard height and designed so they're the same height as the wall cabinets when those wall cabinets are installed 18" above a 36" high counter. If you have custom cabinets, this may not be an issue b/c your cabinetmaker can adjust the cabinet heights. But, if you are using stock or even some semi-custom cabinets, you cannot change the height. You can often get taller cabinets for use w/36" or 42" tall wall cabinets, but not shorter for 30" mounted lower. But, even those that are taller are also adjusted based on standard wall cabinet heights + an 18" backsplash height. Small appliance height...Small appliance manufacturers often design their products to meet this 18" standard...for example, my KA stand mixer (bowl lift) is around 17" and many coffeemakers and blenders are just short of 18". So, you need to be sure you have room under the cabinets + light rail to fit those appliances. Small appliances... Keep in mind that if you're using an appliance on your counter, you must be sure you have room under the base cabinets to move that appliance around easily. Don't, for example, tell yourself you're only going to use it in front of your upper cabinets so you don't need to worry about its fit. In reality, you will be moving things around on your counter while you work and most likely your appliance will be moved under the cabinets at some point. You don't want to tear your light rail off or damage it (or the cabinets). Also remember that "standard" upper cabinets are 12" deep + 1" for the door...so they stick out 13" over your counter...leaving you only 12" or so of workspace in front of the upper cabinets...not much room to work in by itself! (If you have deeper upper cabinets...say 15", there's even less counter frontage in front of your upper cabinets...3" less, so 9".) Vertical workspace... Another consideration is vertical work...

A ledger is a board that is secured just below the counter into the studs. It should be 2" deep by 1" high at a minimum. I have a dishwasher that has granite over it with cabinets on either side and my contractor installed a ledger. You will need to have the panels on either side because that is how the dishwasher gets secured. I learned this the hard way. We reused our dishwasher and it was not designed for securing below granite. They put screws into the sides of the cabinets but the dishwasher went out of square and leaked water all over my wood floor. Fortunately most of the water ran into the basement below and my 90 year old floors weren't ruined. We ended up purchasing a new dishwasher designed to be side mounted. But you definitely need something to attach it to.

prospect711: Thanks for your reply! I had my eye on the Sharp R-820JS, which is the stainless steel sister of your Sharp! (It sounds like an amazing appliance that pretty much does it all!) I just couldn't figure out how to get the size to work. Having a deeper cabinet is a Very interesting idea! I'm going to show this to DH to see if we can somehow swing it with our Ikea cabinetry. Thanks again! (Love your cabinets and beautiful backsplash!) Luv2Laf: Your photo is Exactly what I wanted it to look like! And right next to the fridge seems like such a perfect spot! If only it had convection too - I was really hoping for a little back up oven to cook and reheat small meals. Hmmm... Thanks so much for your reply, gorgeous photo, and the food for thought! colorfast: Okay, so it seems that the microwave/convection combos, unless they are the very wide OTR type, are pretty deep. I'll stop hunting for one that isn't. (No more wild goose chase!) We were planning on having 15" wide cabinets flanking the fridge on either side as a pantry (floor to almost ceiling height), but, maybe we should make one wider set of cabinets instead, where we can put the microwave/convection oven. I love how you have yours next to a counter. That seems to be an ideal setup to me. As for recessing it into the wall, I think we're out of luck, since the wall backs a stairwell leading to the basement as well as the stairs leading upstairs. I'm not sure that we can mess with that. I will share these ideas with DH. Thank you for your reply!