What are the torque specs for my Briggs & Stratton 10hp 204412-147-E1 muffler? Also, should I use anti-seize lubricant on the muffler's 2 bolts?
not very much if they are 1/4" bolts. Use star washers to hold it Anti-seize will prolly cook off due to heat.
This is what I was looking for...
MODEL 200000 HORIZONTAL SERIESENGINE SPECIFICATIONSArmature Air Gap .010 - .014 in. (.25 - .36 mm)Crankshaft End Play .002 - .028 in. (.05 - .71 mm)Spark Plug Gap .030 in. (.76 mm)Valve Clearance � Intake .004 - .006 in. (.10 - .15 mm)Valve Clearance � Exhaust .004 - .006 in. (.10 - .15 mm)FASTENER TORQUE SPECIFICATIONS TORQUEAir Cleaner Base / Backplate 90 lb-in. (10 Nm)Armature 30 lb-in. (3 Nm)Blower Housing 90 lb-in. (10 Nm)Bracket to Carburetor (Snow) 45 lb-in. (5 Nm)Carburetor Bowl Screw / Solenoid 90 lb-in. (10 Nm)Carburetor to Cylinder Head 85 lb-in. (10 Nm)Connecting Rod 100 lb-in. (11 Nm)Control Bracket 100 lb-in. (11 Nm)Control Panel Trim 40 lb-in. (5 Nm)Crankcase Cover 100 lb-in. (11 Nm)Cylinder Head 220 lb-in. (25 Nm)Cylinder Shield 30 lb-in. (3 Nm)Exhaust Manifold / Adapter 180 lb-in. (20 Nm)Flywheel Nut 120 lb-ft. (160 Nm)Flywheel Fan 140 lb-in. (16 Nm)Flywheel Guard 30 lb-in. (3 Nm)Fuel Tank 90 lb-in. (10 Nm)Governor Lever Nut 40 lb-in. (5 Nm)Muffler 180 lb-in. (20 Nm)Muffler Support Bracket 125 lb-in. (14 Nm)Oil Drain Cap � Front (Snow) 130 lb-in. (15 Nm)Oil Drain Plug � Side 100 lb-in. (11 Nm)Oil Fill Tube 30 lb-in. (3 Nm)Rewind Starter 30 lb-in. (3 Nm)Rocker Arm Stud 100 lb-in. (11 Nm)Rocker Ball Set Screw or Nut 45 lb-in. (5 Nm)Spark Plug 180 lb-in. (20 Nm)Starter Cover 20 lb-in. (2 Nm)Starter Motor 140 lb-in. (16 Nm)Rocker Cover 75 lb-in. (8 Nm)Snow Hood 40 lb-in. (5 Nm)Snow Shield 50 lb-in. (6 Nm)
Gas blowing out of muffler
Q
Briggs Intek 25 hp smoking from exhaust
12HP Briggs & Stratton carb mounting bolts won't stay put
18 hp Briggs engine in Craftsman tractor low on revs and power
Wow! If a mechanic actually torqued all of that, he wouldhave been fired on his first day!!!!!
Fish
Of that entire list, the only spec I would use is the rod bolt torque. I use 1/4" drive tools. The longest handle is less than 6". Please note that all those specs are pound INCHES, not pound feet
andyma_gw
UserOriginal Author
Related Discussions
Gas blowing out of muffler
Q
Briggs Intek 25 hp smoking from exhaust
Q
12HP Briggs & Stratton carb mounting bolts won't stay put
Q
18 hp Briggs engine in Craftsman tractor low on revs and power
Q
fisher40037
andyma_gw