This old thread got revisited. @dani_m08 to answer the question about extra probe, I believe I ordered an extra one when I bought the set up. The probe wire is just setting in the junction box I think but honestly I cant remember. When I laid out the underfloor heating and the probe, I just ran another probe near the first probe, and it was then sealed into the floor self leveling compound as per instructions. then the end was just threaded into the wall like the one that would be live, and not connected, but just laying there in the box. Regarding the tile layout. I just decided to run it this way, after getting instructions on the 90Degree way, IIRC. The herringbone that I love is from my childhood and the side walks in my neighborhood that all ran at 45Degree. so that to me is herringbone. I know you posted on @sochi thread about her amazing bathroom and a wall mounted faucet. I would totally do it if I had the right sink for it. In my case I had made my sink out of soapstone and an integrated backsplash. The pictures of this bathroom reveal are no longer available because of the use of photo bucket, when it was Gardenweb. I did not keep my account with photo bucket. I'll add some of the reveal pictures so you can see the sink and floor. Regarding the sink there is no ledge for water to drip from my hands when using the faucet. The water drips right into the sink. In my other bathroom with a deck mounted faucet I am always wiping up drips and it is a nuisance. I much prefer the setup for this sink. Below: I love the flush finish from the faucet to the bottom of the sink. nothing drips on a counter or edge of a sink. Below: looking in from the doorway. Below: Here I am finishing up the sink. the backsplash was epoxied on as a separate piece. The whole soapstone install in the room took next to nothing to buy as they were all small pieces that I epoxied together with a 3 part stone epoxy. Below: this is the counter at the tub, and is in 2 long pieces but I was able to epoxy them together at there edges to make a wide slab for the top. All the soapstone was finished with a 60 grit sandpaper to be rough and this lovely soft tone of blue/green/gray/white. I did not oil it so this color tone would remain light. Below: If I recall correctly @sochi helped me decide on this Hubberton Forge Mirror. I have 3 different metals in this room, but they are all a cool silver to black color. Below: the center of this tower shares space with the kitchen on the other side of the wall. there is also some extra space that houses some electrical wiring. this is an old simple house. this bathroom was an add on when it got move to the farm in the 30s IIRC. The plumbing was all rearrange and some of the details that were orignially there I kept but updated it, such as this tower feature. The old one went and the carpenter did a wonderful job with this one. Below: This feature was another thing I kept from the old bathroom but flipped it from the other end and had the carpenter put drawers in it. Before it was a hell hole. things got lost and the build was soooo old and creapy I didn't like using it for storage. Now it is perfect for storage.

are there bedrooms down there as well? if someone will be using the bedroom in the basement, then they will want a decent bathroom to go with it. 6 inches really isn't worth the hassle of taking down or moving a wall. A foot, maybe, 6" ? no. once you put on the wall or tile, you've got maybe 4" total. Maximize the space by choosing a good vanity w/storage, and possibly building a niche into the wall for additional storage. (use the area between the studs as a built in cabinet) using a prefab shower is fine, but pick a decent one as opposed to those flimsy acrylic pieces. you don't say want the resale value is, so i have no way of knowing how much you should invest. You say you bought mid-range, but I don't know what else you need to redo. anything under a 15% profit really isn't worth it. as for fitting it over the existing drains, usually you will need the new drain cover. if the drain needs to come up, there are extensions. I would advise your husband to do some research on how to fit those into an existing bathroom. If he's handy and can build his own slope, mortar bed and waterproof the shower, then he could prob tile it himself. Just depends on how much work you want to do and what the return is on what you choose. by the looks of what you have there currently, you may have some water damage underneath all the mess. Tear out what you can and then determine what you need to do.

" light grout that is impossible to keep clean " A bath used by males is best with epoxy grout. The Pro tiler needs to have experience using this type of grout. I have it in my baths...it is impervious to any stain / dirt.

I got the cabinets through Home Depot (20% off) they are not higher end but they have held up extremely well and we’ve been happy with them. I don’t remember the brand, but the color is cognac on maple. They’re standard kitchen cabinets. We got 2 regular drawer banks, 1 extra wide drawer bank, 2 sink cabinets and the closet you can see in the picture for about 1800 w/the discount. We bumped the shower wall 6 inches into the bedroom to make the shower bigger, pulled the cabinets out from the wall a couple of inches to provide more counter top. And curved the edge the counter for interest. Just for fun, this is what we had to start with. The tub was rusted and there were two doors, 1 from the hall & 1 from the master bedroom, we closed up the hall door. I think we got our moneys worth. LOL As for the labor, I found my Contractor through a plumber I had hired to put in a kitchen faucet. I asked if he had someone good he could refer and he referred Matt to me. Matt had his own company but just him and his guys. All of his work was by word of mouth, he didn’t advertise or push for business, he didn’t need to. I think I got fair pricing from him because he didn’t have the overhead a lot of the larger companies might have. He wasn’t the least expensive and he wasn’t the most expensive. Finding someone who was willing to work on our schedule and not having to have it done ASAP is what really helped me to be able to keep our costs at a minium for both labor and materials.