I have real oak hardwood in my kitchen, and three years ago I installed engineered, handscraped hardwood by Appalachian Hardwoods in my bedroom. The engineered hardwood is superb. It didn't even scratch when we had heavy, sold bedroom furniture installed. These pieces require four people to move, and at one point it was dropped on the floor: no scratches, no dents. We now have felt pads on all the furniture for more protection, but the engineered wood has held up well. It's also easy to clean. It was more expensive than some hardwoods: $8.00 per square foot! Since our home was built to look like an old Louisiana antebellum home, I wanted floors that looked old and had character. The handscraped engineered floors fit the bill, especially when compared to the price of real, reclaimed wood from old homes or barns! Now I'm replacing all the flooring in my house with the same engineered wood. I'm even removing the oak plank in the kitchen. It has not held up over the years. The finish is gone in some spots, probably from wear and the use of things like vinegar, grease, etc. Some things really seem to eat away at the finished oak regardless of how quickly you remove a spill. It also has some dings from me dropping heavy cast-iron cookware. So, I can only speak from my experience, but so far the engineered hardwood seems to be the better choice for my home. Plus, it was faster to install. If I had done raw hardwood, the contractor said he would lay the wood in the house for a week to let it "cure" before finishing it. I live in a high-humidity area (NC). I'm impatient and didn't want to wait.

So let's talk the about the difference between an engineered hardwood and a vinyl plank. And there are more than just the difference between the two flooring options. There are many differences within each type of flooring. For example: engineered hardwood flooring can come in different thickness overall and vinyl planks can come in different plank styles (glue down, WPC and SPC). Let's break this down for you guys a little further. Engineered hardwood is an incredible option for an authentic with longevity in mind. Typically is worth less than it's hardwood counterpart (hardwood) but in some instances, depending on the wood species, a high end engineered hardwood veneer could be worth more than a low grade hardwood such as your North American (domestic) species. Engineered hardwood is more often on the 7/16" side of thickness and that is your more price friendly thickness. You can special order a thicker 3/4" board, but that will come at a heftier price because it's added layers. The added layers create a more stable plank that expands and contracts at a lower rate than it's 7/16" counterpart. Engineered hardwoods always should and for the most part come prefinished with an aluminum oxide coat. This very coat is your barrier against everyday beatings from walking traffic and dropped items. This coat is very tough but no floor or finish is indestructible. You will have dents and scratches pop up over the years. Depending on the company, you can buy "refinish kits". Although, technically you cannot refinish aluminum oxide, the kits just help you hide the scratches until you decide to do a professional refinish to your floor. Lastly, let's talk about refinishing your hardwood floor. Please have a professional do it! And it is very expensive to do this job. Depending on your floor size it can cost well over $3,000 USD. At this rate, you are in the market for a high level LVP. Which brings me into the luxury vinyl plank spectrum. As you all are aware, LVP's are dominating the flooring market and they should be. They do a very, VERY good job at imitating a hardwood or stone surface and multiply the longevity all the while. Vinyl has come a long way in the last couple of decades let alone the last few years as far as planks are concerned. There are plenty of options and so, so many different brands all wanting you business. Luxury vinyl planks can be divided into two different categories in the market right now: glue down or floating. The first generation of vinyl planks are your glue downs. They are still very popular and serve as one of the friendliest DIY repair floors. You simply heat the old damaged plank, peel it and put a new one down. The floating aspect of planks gets a little more complicated as you can have a WPC (wood polymer composite), SPC (stone polymer composite) or a loose lay style. And you can look those up to see the complete difference in each to see what's your most needed. I'll lightly go over each to explain what they are. While all three styles are virtually waterproof, you really can't go wrong with any and will have a good product in each one. WPC's are a click based plank which does not require an underlayment, hence being labeled a "floating" floor. The foaming agent in the core of the plank helps with sound absorption and makes the plank a little more friendly to stand on. It's a thicker overall plank and you should think about how the trims will be affected. SPC's are a click based plank which also does not require an underlayment which helps reduce the installation cost. The core is limestone based and makes it very rigid and tough. It's extremely dent resistant but for the most part is lower in wear layer for some reason. You can however find plenty of SPC's with a higher wear layer, nearing 28-30 mil, but it will cost you more because you will have a high dent and scratch resistance. And finally you have your loose lay planks which are the ultimate form (as of now) in easy maintenance and installation. They do not require an underlayment, do not use a click system and don't need any adhesive (although some installers recommend gluing the perimeter). They have a friction backing which let you lay the plank adhesive free without any movement on its end. The plank itself is waterproof and pretty dent resistant. While engineered hardwood does cost more and is less maintenance friendly, it does add value to your home with the hardwood veneer. The ability to refinish gives you a long floor life but the cost of a refinish is a setback in itself. Luxury vinyl planks are a low cost and long lasting floor option but adds little to no value to your home. The endless options of styles and colors gives you endless customization to your home at a far less price. Either option can last a while but at this time vinyl planks are a better option for any household with multiple members, both human and furry alike. I hope this little bit of information helps in the short and long run. Just a flooring dude.

If you are on slab, I'm not sure what you would be nailing TO. Adding in a sleeper subfloor would be very expensive and will still require a vapour barrier underneath. *Technically a glue down SOLID hardwood can be done on slab - but it isn't recommended unless your HIGH END flooring installer has done it successfully in the past. A glue down engineered floor is technically "more stable" in the widths they are suggesting, but I would question a comparison to a 2.25" solid hardwood. Especially if the solid NARROW strip hardwoods are rift or quarter sawn. The same adhesive would be used regardless of plank structure (solid vs. engineered). The RIGHT adhesive (aka. EXPENSIVE glue) MUST be used over slab in TX. And then the proper SPREAD RATE must be used (lots and lots of the expensive glue will be required) as well as the PROPER TROWEL profile/depth will be required. These expensive adhesives ($100/gallon is common) will achieve 30-50sf per gallon. These adhesives will be the vapour barrier. The most expensive ones will have "limitless" moisture content as one of their key features. Even with the TOP adhesives, the installation will still be cheaper than a sleeper subfloor + nail down installation. The sleeper subfloor would mean a lower priced flooring professional can be hired to achieve the nail-down installation. The glue down method will require the higher skilled professional with all the knowledge required to install a glue down wood floor PROPERLY. And the next issue is the HVAC system. Regardless of the installation method, your HVAC will have to have the ability to maintain a CONSISTANT level of humidity. Sometimes A/C isn't enough in high-humidity environments. Sometimes a whole-home dehumidifier is required in extreme humid areas. Please review your HVAC system's abilities to TIGHTLY control humidity (somewhere around 40% is PERFECT...and it must be maintained 24/7 for the next 25-60 years). Start there. Spend more money for the upgrade on the HVAC system so you can have the wood floors - regardless of width/composition.

Turns out the boxes are labeled in that way: "Revwood", even if the actual product is Revwood Plus. There is an insert instead with "Revwood Plus" printed on it. Also, if you were using Mohawk MoistureGuard or SoundGuard or SilentGuard underlayments, the brand name shown on the label is "Performance Accessories". I have seen the blue colored one (MoistureGuard) is "Value Underlayment" and the white one (SilentGuard) is "Premium Underlayment". Confusing choice by Mohawk.