Open cell foam does stop most of the airflow, and it costs a bit less than closed cell foam; however, it is spongy and can retain moisture. There are at least two ways that moisture can get inside the wall. Water vapor can migrate into the wall, which a properly-installed vapor barrier should prevent. The second way moisture can be present in the wall is via condensation. The warm air from inside the home will meet the cold air from the outside somewhere within the wall cavity. Where the two temperatures meet, moisture is created. When one uses only open cell foam, the condensation will form within the foam, but won't be able to dry out because the airflow has been cut off, potentially leaving wet insulation which could lead to unhealthy mold. Building science offers that, if a home is heated during the winter months, the best way to prevent condensation from forming in a wall is to be sure that 50% of the R-value in the wall is closed cell foam. The remainder of the cavity can be filled with open cell foam, fiberglass, or any other insulation. Because the cells of closed cell foam are solid, they can't hold moisture. By following the 50% rule in external walls, the hot and cold temperatures will be forced to meet within the closed cell foam, condensation will be neutralized, and you'll have a wall that is air-tight and moisture-free, making the use of closed cell foam as the first line of defense against Mother Nature well worth the investment. Linda - Foam It Green http://www.sprayfoamkit.com/videos-a-how-tos/insulating-a-2x6-wall

5 tons seems high to me. A manual J calc shold be done. My 2000 sq ft in central Florida has a single 3.5 that keeps the house as cool/warm as we want in weather extremes. Check out my energy rants for other ideas. Being in the south like us, most of the ideas will apply to you. We have average $130 power bills in the summer. Currently the U.S. is sending an exorbitant portion of it's energy money overseas. Anyone who does not take some initiative to cut their power bill (and therefore energy usage) needs to realize that they are providing 'aide and comfort' to those who would love to see us dead and are taking great delight in our current difficulty. Drilling for more domestic oil is not the panacea for this mess as prices are not being controlled by the mechanism of supply and demand, rather by a combination of speculators and OPEC who control such a large portion of the world's oil supply that they can easily negate any of our drilling efforts by simply closing the tap at their end just a little. Any oil we produce won't save us any money. We currently produce a large amount of oil in Alaska but do you see us getting a break on it because it's domestic? No, we pay the going world rate, set by the aforementioned OPEC and speculators...and provide another windfall for the oil companies. They sit before Congress smiling saying their huge profits are necessary to allow them to explore....excuse me....we are talking about NET PROFITS here...what's left AFTER exploration expenses. We the people have no control over this sort of manipulation of our government, whether we have Republicans or Democrats in charge. . .there's too much money involved. Our only hope is to cut energy usage, not drill and give them more avenues for profit. We all need to realize the best thing we can all do to help the energy situation and economy is to take individual action. Rather than waiting around for the government to do something we can each cut our electric usage dramatically....up to one half of your bill if you are willing to spend a little time and money. Every time you see your power bill shrinking, that's money for you rather than some oil producer. Money you can spend here to help the economy or save as you prefer. Here are several sites worth visiting that aren't selling anything but tell it like it is. Plenty of simple and painless techniques to cut your power bill. http://michaelbluejay.com/electricity/ Mr. 'Bluejay' does a great job explaing away a lot of scams...see his section on surge suppressors for example. http://www.builditsolar.com/index.htm Be sure to look at the 'Half' program. The current situation has people grasping at all sorts of non-cost effective solutions that sound great on paper but don't hold up to scrutiny in the real world. Solar electricity is one of those as would be wind power in cent. Florida. Solar PV (photo voltaic) just costs too much at the present. Hopefully ongoing research will change that in the future but it's not ready for prime time yet. The rental program below will probably be practical if it gets underway. Check out this site for info on a possible contender for solar PV at home. http://renu.citizenre.com/index.php?c=1218495642 The 'Build it Solar' site also has some good info about costs. http://www.builditsolar.com/Projects/PV/pv.htm Plenty of outright scams getting too much press also. The 'run your car on water' crowd is one I can think of (apparently many people didn't pay attention in high school physics). A good site explaining the physics that negates that scheme is here along with other interesting info about some of those behind the current revival. http://www.alternative-energy-resources.net/browns-gas-the-reality.... Another scam that's been revived is the 'phase controller' that supposedly saves electricity by making motors run more efficiently. Home show demonstrations with an electric motor show it's electricity usage dropping dramatically when the motor is plugged into the device rather than straight into the incoming power. These devices actually do work in the applications they are designed for...this has the unfortunate effect of helping the scammers (or to give them the benefit of the doubt, uneducated-in-electricity folk) sell these things. An industrial application that produces savings would be a big table saw in a woodworking shop that runs constantly. When it's not cutting wood, the motor is under no load and at that moment, a phase controller will save energy. The goal of electrical engineers is to make sure anything with a motor runs that motor at rated capacity at all times...that's the point a motor is most efficient. Their striving for this is what has made ACs and refrigerators much more efficient lately. The point here is motors in your home all run at rated load all the time. There is no 'off load' time like with the big table saw. A 'phase controller' saves nothing in this situation. In hot climates a proven strategy that works well is a heat recovery unit attached to your AC unit. It provides free hot water and also increases the efficiency of the AC a couple of SEER points by reducing head pressure (and electricity draw) on the compressor. You're paying for your A/C to move a great deal of heat out of your house, you might as well use that heat to provide you with hot water. Adding one of these to an older AC unit that still runs well is a good way to cut $30-$50 off your monthly power bill during AC season (which here in cent Fl can be about 9 months). The neatest thing about this solution is that it's cost-negative. In addition to being free hot water as opposed to other 'high efficiency' heaters that still consume energy, it actually lowers your cost of air conditioning. Here is a manufacturer's site for two of these and a power company document about it as well. The second mfg site has a neat calculator for your savings...but my experience shows it to be somewhat under-optimistic. I don't think it's taking into account how a hru will improve your AC's efficiency. There are claims that they don't work with higher efficiency unit, but I have two HRU connected to 13 SEER heat pumps that provide plenty of hot water. http://www.trevormartin.com/about.asp http://www.turbotecproducts.com/EPhome.html http://www.p2pays.org/ref/11/10104.pdf Another real saver in hot areas is a radiant barrier in the attic or metal roof. Both create similar savings. If you are re-roofing, consider changing to a metal roof. When installed over a normal wood-decked roof, noise is not a problem. Most people thinking of a noisy metal roof have heard one that's been installed over wood 'stringers' as was the case many years ago...very noisy in a rainstorm. If you have a hip roof house or a lot of dormers metal may be too costly due to the waste from all the cutting to fit...metal is most cost effective on a two-slope 'shed type' roof. Radiant barriers can either be installed during construction..an easy way is using foil-backed plywood roof decking ...or added later. See this site for info and material. http://www.atticfoil.com/ Tankless water heating is also a problem area for accurate claims of savings. A gas tankless heater can be much more efficient since it eliminates the flue that passes through the center of a conventional tank heater and becomes a chimney to carry away your water's heat once the flame shuts off. Electrics are another story... Big savings are claimed that are not supported by data. No studies are shown that give specifics telling you what make/model/year tank unit is being compared with the advertised tankless. Maybe they use an ancient cast iron tank heater insulated with sawdust? Verifiable details please. Somehow electric tankless heaters dodge the requirement for the yellow government 'EnerGuide' label that every other appliance must have. If they had to carry it, their claims would show to be false. Claims of better durability because of 'no tank' are a red herring also...the 'tank' still exists, only it's now smaller. Buildup from hard water deposits may be more of an issue with tankless, possible surcharges from the power company later due to high instantaneous current draw, heavy wiring needed, new construction with planned tankless can make retrofit of tank type later very difficult due to lack of dedicated hot water piping, incompatibility with future solar or other alternative power sources due to aforementioned high current draw. These are all serious disadvantages of the tankless electric. All electric hot water heaters are 100% efficient at heating water. That's a function of an electric element immersed in water. The only added efficiency of a tankless is the reduction of standby losses which are very minimal in new technology insulated tank heaters. Put your hand on one and you'll see they pretty much run at room temperature...very little standby loss. Another myth is that shading a A/C condenser saves '10-20% or more. The reality is not much. Similar situation to a garden hose left out in the sun...you turn on the water and what comes out is scalding hot....but in a few moments the water is cool...sun impinging on something will make it very hot but that is a function of 'accumulated heat'. What heat is striking something and being carried away by a fan is very small. See the following link about this subject... http://www.fsec.ucf.edu/en/publications/html/FSEC-PF-302-96/index.htm A free, online calculator that can help you plan upgrades is here: http://hes.lbl.gov/ Two technologies have the potential to really turn things around..see these two links for something both companies say will arrive sometime next year...Still better to get moving with your own plan that to wait with your fingers crossed.. http://www.eestorbatteries.com/ http://www.nanosolar.com/ Please use due diligence when deciding on ways to save energy. There are LOTS of scams out there. The internet is a great source of info and you can easily see both points of view on any energy saving strategy. Just simple conservation by time-tested means is still the best way to approach our dilemma. If we all cut our power bill in half, we'd all have much more money in our pocket and our nation would be much more secure. This action, along with Mr. Picken's ideas on wind power, WILL free us from imported oil and rather quickly. Pick plan with garage shielding house from sun...i.e. not one with a garage on the side or end of house. Remember in Florida, it's all about solar heat gain..through the roof, windows, and walls. Choose a lot that allows you to orient house with garage on west side facing afternoon sun. This allows garage to block afternoon solar heating of the part of the house 'hiding' behind it. Minimize size and amount of west facing windows and doors. Use double pane, low-e glass in vinyl frame windows and fiberglass or vinyl doors. Plant trees and large shrubs to shade the west side of the house. 10' ceilings are desirable. Although you have more cubic feet to cool, you'll feel more comfortable at a higher temperature. A higher ceiling allows the air to stratify. The warmer air will accumulate at the top, well above your head where you can't feel it, the cooler air will sink, making the 'lower level' you live in more comfortable. With a high ceiling, activities that generate heat such as refrigerators, dish and clothes washing, showers, etc., that introduce heat into the living area have their heating effect minimized by the heat-at-ceiling stratification. Ceiling vents in a high ceiling house should be directed down rather than trying to spread the air sideways. Sideways deflection mixes the air, defeating startification. Ceiling fans are not as effective with the higher ceiling as they tend to dislodge the hot air and send it down, causing the air conditioning to run more. Spring or fall, when the windows are open, is the best time for ceiling fan use. Small pedestal fans and the popular 'tower' fans work better during AC use, circulating the cooler, lower level air. Air movement from them may let you set the thermostat higher and save energy. Running a ceiling fan in the winter to 'get the hot air back down' is counter-productive as any reclaimed heat won't compensate for the wind chill effect you'll feel. With 10 foot ceilings, a floor level air return is preferable to minimize disturbance of stratification but with normal 8 foot ceilings, a ceiling return will make the structure more comfortable by evening out the temperature. Have 24" roof overhang to shield windows and much of the wall area from midday sun. The goal is to allow maximum view of clear sky from all windows to minimize need for interior lighting during the day without direct sun entering house during the summer. A 24" overhang will usually do this in the summer , while in the winter, the lower position of the sun in the sky will allow it to shine in for some solar heating although the desired low-e window glazing will minimize that. Be sure the engineering is correct for the wind load where you are building. Two story structures in Florida require extra planning to minimize heat gain as they usually present more wall area to the sun. You lose the 24" overhang advantage shielding the windows and walls on the lower story. This can greatly increase solar heating through the windows and walls of the lower floor which will then convect the heat to the upper level. This is an advantage in northern climates but a liability in the south where cooling is the main concern. There is some advantage here in less roof/attic space, however.. Use hip roof construction...much stronger than gable design...will qualify you for a substantial discount on your windstorm part of your insurance. Check with your agent. Use either galvanized ('bright metal', no colors) roofing...expensive, especially on recommended hip roof designs (a lot of waste cutting the metal with all the angles of a hip roof) or use a radiant barrier. This barrier can either be an aluminum/Mylar film draped over the trusses before the decking is applied or applied on bottom of trusses in existing structures or plywood decking with pre-applied barrier. The radiant barrier will keep the attic much cooler. Plywood makes a much stronger deck material than OSB at a minimal premium in price. Use a roof design with 6/12 pitch. This gives sufficient attic height to maximize convection cooling. Also 6/12 is the 'sweet spot' for wind resistance. As roof pitch gets lower, the tendency of the roof to act as an 'airplane wing' in a windstorm increases raising the chance of roof lifting off. A greater pitch begins to act as a direct barrier to high winds increasing chance of 'push over' failure. A 6/12 allows wind to slide up and over but also creates turbulence on the lee side minimizing lift as well as generating more down force on the upwind side. Try to keep square footage as small as comfortable for you. A 4000 sq. ft. home requires far more energy use than a 1500 sq. ft one. In Florida, build concrete block on a slab. We have hurricanes AND termites here...Code requires ground pre-treatment. Continuing the termite contract is cheap insurance. An extra benefit of on-slab construction is being able to take advantage of the cooling effect of a slab floor. The earth under a house stays fairly cool and especially with some hard surface flooring the small difference in temperature between the earth and the floor surface means very little heat gain from below. Its helpful to think of heat as a fluidÂjust as water flows more forcefully as height of fall increases, heat moves quicker across a greater temperature gap. Use several solar powered attic roof ventilators along with numerous passive vents. In Florida you can't have too much attic venting. We don't get enough cold winter weather to be an issue if you're well insulated. Use R-30 or better in the attic. Insulated cells in concrete block walls are probably not worth the expense. Florida requires so many cells to be poured concrete now for windstorm resistance thereÂs little empty cells left to insulate. Check the Florida Solar Energy Center website and youÂll see that less than 17% of heat gain occurs through the walls (not entirely accurate for two story construction). Also keep in mind that there are many windows and doors that deduct from the wall area and upgrading them will have far greater effect than some fluff in the block cells. A better solution is a foam Âunderlayment beneath the stucco on the west side of the house. Be wary of spray-on underside roof insulation. This may prove to be a time bomb as the roof ages and begins to leak. The decking and trusses may be seriously compromised before you become aware of any leak problem. The 'sealed' nature of the insulation envelope may well lead to extreme damage in the long run. Use fluorescent lighting wherever possible in place of incandescent. LED lighting will be preferable when it becomes more cost efficient Refrigerators are a substantial user of power. Since about 2000, efficiency has been greatly increased in the new units. If yours is old, consider replacing it. Check the energy labels and youÂll see that top or bottom freezer models have consistently lower power usage than side-by-sides. Small access doors to get drinks out are handy and keep all the cold from getting frequently dumped out if you have children opening the fridge frequently. As in house sizes, get the smallest refrigerator you can be comfortable with. Note that external ice and water dispensers take up a lot of interior room and tend to make people buy a larger unit to compensate. Unless you are really tied to using a separate freezer, todayÂs high energy prices far outweigh any savings youÂll get by buying food in bulk and stockpiling it at home. The possibility of increased power failures from more frequent storms and the accompaning food loss also makes freezer use less attractive than it used to be. Point of use hot water heaters can't prove measurable savings. Tank type heaters have such good insulation now that standing heat loss is minimal. Point of use systems will quite likely lead to surcharges from the power companies in the future as the high instant current draw becomes more of a problem during peak power use time. Only tankless gas units can lay claim to significant energy savings due to the elimination of the central flue in a conventional gas tank type heater. There seems to be a lot of misinformation being pushed about AC efficiency. Code requires a minimum of 13 SEER rated Heat Pump equipment. 14, 15, 16, and higher are available at much greater costs. Research will show the only difference between the very expensive high efficiency units and a higher quality 13 SEER is the amount of condenser coil and the controller PC board (also a fancier cabinet). They all use the same brand and model compressor (Copeland Scroll), the same fans, reversing valves, driers, etc. Most companies trumpet the boards as being the key to their high efficiency, this is mostly smoke. When the 'rubber hits the road', what counts for amount of electricity used is how efficiently the compressor can transfer the heat from one place to another. The compressor is what's putting that 12 to 20 amp load on the line. The more you can reduce that value, the lower the electric bill will be. The compressor is moving the refrigerant gas from an area to low pressure to high. That's the work it's doing that runs up your electric bill. As the gas enters the high pressure area, the condensing coil's job is to cool it and cause it to shrink. This shrinking lowers the high pressure and puts less back pressure on the compressor. This has the effect of reducing the work the compressor must do and therefore lowers it's amperage draw. An amp meter is a handy tool for the energy conscious homeowner as it will let him see in real-time what effect his efforts to conserve energy have. You can put it on your heat pump as it runs and perform a simple experiment. First hold a couple of sheets of cardboard against your condensing unit's grill as it runs. You'll see the amperage begin to increase as the compressor's workload goes up since the coils can't shed as much heat and shrink the gas. Second, remove the cardboard and spray a fine mist from your garden hose on the coils and you'll see the amps go down as the coils become more efficient from the evaporative cooling of the water and shrink the gas quicker. Keeping the coils wet all the time would lower your cooling bill but would also corrode the coils so is not a good idea. The way to accomplish this safely is to add a unit called a 'heat recovery unit'. An AC professional can install this by cutting the discharge line from the compressor and sending the hot gas through the recovery unit then back to the condensing unit. The heat recovery unit is a 'heat exchanger' that has two pieces of copper tubing wound tightly together and enclosed in an insulated box. One piece of tubing is the loop carrying the hot, high pressure gas from your condensing unit. The other makes a loop to your hot water heater. Whenever the AC is running, the small water circulator pump in the heat recovery unit turns on and in effect does the same thing squirting water on the condenser coils did as it circulates water through your water heater.The heat from the hot gas transfers through the walls of the tubing into the water causing the gas to shrink and cut the compressor workload. In addition, the unit now provides free hot water for your house, allowing you to shut off your water heater in the summer. These two savings together can easily total $50 a month (!!!!) on your electric bill. Remember, in addition to lowering the workload on the compressor and saving electricity there, your water heater is no longer online. An interesting side benefit is that the more you use your hot water, the lower your electricity bill goes. This doesn't mean using more water (longer showers, etc) but you can set your washing machine to use hot water rather than cold or warm and get cleaner clothes AND save energy. You are using that water anyway and by using it hot, you are 'shedding' heat from the system and increasing it's efficiency. Heat recovery systems are typically less that $1000 and FAR more practical than solar water heaters that have much more complicated control systems, are far higher maintenance items and cost much more. Pushing solar hot water in Florida is doing the consumer a great injustice. Heat recovery units are said to not be practical on high efficiency systems (15 +SEER ratings) but the addition of a heat recovery unit to a 13 SEER system probably raises the entire system's efficiency to the 15 or 16 SEER range if you bring the savings of the water heater into the equation. Water heaters are typically resistance element heaters...the most inefficient way to heat. The industry is cashing in on energy fears by adding more coils to their units and charging a premium for the 15 and 16 SEER units that's much higher than the cost of adding a recovery unit to a SEER 13 system. The higher efficiency unit may save cooling cost but then 'wastes' the perfectly good heat that could be put to use for your hot water by just Âblowing it away outside..

Considering insulative sheathing has made it's way into prescriptive minimums, I think it's more of a requirement than allowment. The "+" value in wood framed wall R value below denotes insulative sheathing prescriptions. Typical framing results in walls where 20-30% of a wall's total area, has no cavity insulation, which drags down the entire wall area's performance. For owners or designers after the most "R per inch" insulative sheathing is more effective than cavity insulation as it better encapsulates framing and structural components. This potentially increases airtightness, reduces thermal bridging and keeps structural components warmer, reducing chances of condensation and rot. The last feature may be why codes are beginning to adopt insulative sheathing as best (minimum) practice and calculating the minimum insulative sheathing is important for wood framed walls in cold climates. In the warmer climate zones of 2 and 3, a 2x4 wall with 1/2" of insulative sheathing outperforms a 2x6 wall and is thinner. As for Open Cell foam in roofs, I agree it's a relatively new practice posing risk and the same is true for Closed Cell. That's why many experts recommend insulative sheathing on top of roof structural sheathing and why the traditional unconditioned attic is appealing, as long as it has an airtight ceiling plane (tough part) and a thick layer of loose fill insulation. Roof leaks are typically more common and damaging than condensation and I think closed cell complicates discovery and repair more than open cell, but in cold climates I would prefer closed cell. Martin's article sounding the alarm about modeling studies is useful, but I think the onus mainly falls on field results and the vast majority of open cell roof decks seem to be working fine, other than the unfortunate reality that most spray foam installations are below code minimum performance. A good friend of mine is building in TN and we just went through all this. He was able to get good pricing for a flash coat of closed cell against the bottom of the roof deck, followed by filling the rest of the rafter cavities with open cell.

Nothing about your home should keep you up at night. If concerns about using a particular construction material or method will do that, then don't use it. However, if we never applied any new materials, systems, and construction methods in residential construction, our homes would be no more comfortable and perform no better than homes built in the 1700's. We wouldn't have, for example, air conditioning, which makes living here in coastal Virginia much more pleasant in summer and which keeps certain contractors in the Houston area employed. The energy crisis in the 1970s gave rise to the use of house wraps and vapor barriers which caused plenty of unintended consequences. That doesn't make polyethylene or house wrap bad materials, it's simply that the building science wasn't established at the time. We continue to rely on the researchers to thoroughly test new ideas (and real world testing is better than computer simulations) to minimize, if not preclude, unintended consequences. When considering the use of the latest and greatest materials homeowners would be well advised to remember the old adage: The early bird gets the worm, but the second mouse gets the cheese!