I wrote this in the other post (rmkitchen updates) so I'm just copying it over here gglks -- the paint is Aura (Benjamin Moore) Frappe, AF-85. I have to say I haven't noticed any fingerprints on the sink ... but there are water spots (inside and on the rim). But of course, those just wipe right up with a sponge (when I'm so inclined, ha ha!) I'm not a belt-wearer but my husband is, but we also haven't noticed any scratching on the outside of the sink. I just went and double-checked: no fingerprints, no scratches. There are some scratches on the bottom of the (interior of) the sink and, as I wrote, water spots, but other than that, nothing. And I only noticed the scratches because I was just now really looking for blemishes. The sink is Bates and Bates Farmhouse 12 Gauge Satin Stainless Sink.

As far as I can tell, the nig bummer is that its meant to be a partial overmount with a flatish lip that goes over the counter. Unless you caulk well while installing, its moldville under that lip. I like that it's easy to clean and it always looks white. We got a third party grid that helps to keep pot marks away. The LACK of depth is a relief, I like the sink around 8 inches deep. If she uses 1/2 sheet pans frequently, she needs a different sink as this one will not fit those size things. I have a two burner pancake griddle - the cheap non-stick, for home use kind - and it won't fit that. It can sit on the top, and the front and back handles will rest on the sides - so I can still clean the pan. It will fit a regular roasting pan. The other two things that I don't like about the sink is the faucet is very far back (23" or so) in comparison to 19-21" for most undermounts. It acts funny if its filled with ice - just like a glass of iced tea, it will form condensate on the underside of the sink. I imagine that varies with where you live. I will get you a trash pullout picture soon.

Elkay: In case you didn't believe this is a retrofit, here is a "before" picture. The new cutout has bisected the grinder slot that held the sink clip. That's the arc that is filled with stone and color matched adhesive. The plug in the front is the reinforcement rod slot having been ground back and filled. Not bad. I never point these out to the homeowner; once you do, she can never "unsee" them. Run this thread past your technical guys, please. I can't wait to hear the "It can't be done." The secret? Because the bowl is deeper than the apron, you have to tap the cabinet front off. If you put the sink in, you can't get the cabinet front back on. If you put the cabinet front on, you can't get the sink in. You partially put the sink in place, partially put the cabinet front back on, more sink, more cabinet front, until you're done. I never use your provided clips; all my retrofits are strapped in place. Throw a couple of Sink Straps from Regent Stone Products in the box instead, please. Keep making these please. They are moneymakers and the customers love them. Just under 3K.

To the OP, if you decide on an apron front sink in stainless steel, make sure to look at how the front panel is made. You don’t want a curved one. You also don’t want a SS apron front that is super thick. What Joe Corlett pictures above is more what you want. Some of the cheaper ones have the super thick apron - it intrudes into the usable floor area of the sink. An extra-thick apron also removes the ergonomic advantage of an apron front which is that it is easier on your back to have your body directly against the sink, than to have the slight lean required with an undermount sink with its several inches of counter in front of it. I like the design of the Elkay apron front sink, because it also has an offset corner drain, an advantage. However, I don’t have direct experience with it so I unfortunately can’t advise on whether it’s a quality sink or not. What you DON’T want - this apron front is more than 5” thick: The Elkay ECTRUF30179RC, https://www.homedepot.com/p/Elkay-Crosstown-Farmhouse-Apron-Front-Stainless-Steel-36-in-Single-Bowl-Kitchen-Sink-with-Bottom-Grid-and-Drain-ECTRUF30179RC/305866142, the apron front is 2-1/2” thick.