(Corrected) Cracked Corian Sink

11 years ago

We have a Corian counter & sink. The sink has a large crack,
the result of a poorly insulated window, cold air + hot water. We were considering having the existing Corian sink cut out, replaced with a stainless steel sink insert, with its edges on top of the counter.
However, a reputable home renovator informed us that the whole counter needs to be replaced. Has anyone had similar experiences with our preferred solution: replace with a stainless steel sink insert, not the whole counter?
Thank you in advance.

Featured Answer

PeterH2

11 years ago

Cutting Corian is easy enough. Standard woodworking tools like a jigsaw, trim saw, oscillating tool, router, jab saw, disc sander, orbital sander, and belt sander might be used. Slow and steady is best. Personally I would not use a reciprocating saw ("Sawzall") - I find those too violent/hard to control for precise tasks - but I am very conservative by nature; I'd rather spend a little extra time to avoid risk of doing damage.

Most of the cut will be simple; the hard part will be getting into the corners. That's where a jab saw could be useful - being a hand tool it's slow, but that's not a big problem for short cuts.

The corners should be radiused no less than 1/2". The edges should be rounded over and smooth (no chips or cracks). These steps are necessary to reduce the risk of cracks developing and propagating.

Maybe you can find a sink that will fit almost exactly inside your existing one, but I think that's less likely than finding a slightly larger one. You have to consider the shape as well as the simple dimensions.

Since you almost certainly can't increase the size of the bowl very much, I envisage cutting the existing bowl off flush with the bottom of the counter, then enlarging/shaping the opening slightly as required. During the cutting, the bowl will need to be supported from underneath to avoid it breaking away and causing damage.

The whole cutting/finishing job should take less than two hours.

This post was edited by PeterH2 on Sat, Dec 1, 12 at 19:03

Comments (8)

PeterH2
11 years ago
There is no mystery here: so long as you have space in the sink cabinet, you can cut out the Corian and install a top-mount sink as you describe. The "reputable" renovator sounds like they want to make money off you.
Rake4Leaves
Original Author
11 years ago
Exactly what we thought about this so called "reputable" home renovator. He really wants to make some extra bucks from a truly unnecessary project.
Now, to find another renovator who's on the same page as us.
Thank you for your response.
Related Discussions
how tough are modern Corian sinks?
Q
Comments (2)
You are in the minority if you found a Corian sink easy to deal with. Most people hate them for the very reason you said you loved it. They require that bit of softscrub with bleach on a regular basis. No other sink needs that. That's why Silgranite has become so hugely popular. You can do all of your torture tests to it and it's fine. As far as "making them like they used to", no, they are slightly thinner than the old days, and they handle thermal shock less well. You can pour boiling water down the sink, IF you run cold water at the same time to mix it. Corian only cracks if a hot pan is set on it at a seam join. And it's not a sure thing. You could do that 500 times and be fine. But #501 might get you if it were a particularly cold day in the house, or if that was a particularly big bit of thermal mass in that pot (full of soup for instance) or even if the moon's gravity added just the right pull to add that scintillion of extra pull. If you treat it like any other counter top and are just a bit careful with it, it'll be fine. No countertop recommends setting hot pots directly on it's surface. Or cutting on it. Or dropping heavy objects on it. But, the really great thing about Corian is that if it does be become damaged, it's repairable.
...See More
Possible to remove a vitrious china undermount sink from Corian?
Q
Comments (21)
I am happy to report that the sink has been excised from the Corian! It's now on my DR table (which tends to be my overflow project room) and I spent a few hours last Saturday looking through the remnants at nearby stone yards here in southern Maine. Yikes - what a variation in price! In one very close to my home, I saw a remnant of imperial Danby Marble that was beautiful with the sink, as the soft tan in it was picking up the crackle finish in the sink. I made my vanity in the powder room from an antique bureau. I need a top about 23 x 43, and currently have a 3" back splash. That place quoted me $1050.+ :-( Current top, which I'd save and possibly use again someday, if I tire of the sink above. I went to a much smaller two man operation, and while they didn't have a remnant that I liked as well, their price, including templating and install, was approx. $400. :-) I left my name and they saw the faucet handle that I lugged around to hold up to the stone, so they know what I'm looking for. I'll check back with them from time to time to see what else they may have. I also saw this overmount sink in a painted wooden top in the link below, and if I can't find some stone that doesn't break the bank, I may go this route. I could also do some faux marble painting, in either something like the Imperial Danby or what I think the dark green marble is above - Empress Green? I think that a soft white with tan veins, along the line of what I did on this little antique table with gray veins below might be best in my home, though. Here is a link that might be useful: Another possibility - stained or painted wood
...See More
Correct sink installation? Hercules Universal Sink Harness Kit?
Q
Comments (13)
Old thread, new question. It was suggested to me on the bath forums to use the hercules harness. I watched the video and it seems easy enough. The video shows a double sink so the long piece is under the center of the sink. I'm not sure where to place that part when installing a china/porcelain undermount sink on granite, because of the plumbing in the center. Can it be off off to one side and have drain between the wires? I believe the countertop place does drill and give you clips, but the sinks are not installed for you. Which forum should I ask about transporting a 72" piece of granite with double sink cutouts. We have a tahoe, but you aren't supposed to lay it flat. It's from a home surplus type of place. For $100 they will deliver. Any tips?
...See More
Corian AND stainless sink
Q
Comments (7)
Some clarification. These are called mixa sinks the point is corian sides and a stainless steel bottom. You are correct this configuration is completely worthless. I'm trying to find out if a large single sink with corian sides and the stainless bottom is available in the US. They seem to be in Europe, the UK and Australia....
...See More
friedajune
11 years ago
Is the sink and the counter all one piece?
? Or is the Corian sink separate from the Corian counter?

This post was edited by akchicago on Sat, Dec 1, 12 at 13:43
PeterH2
11 years ago
The one big question in my mind is whether you can find a top-mount sink that is exactly the right size to fit inside your cabinet, just a hair bigger than the existing sink, and able to line up with the faucet hole(s)? Making sure of that should be your very first move.
Rake4Leaves
Original Author
11 years ago
Yes, the counter and sink are all one piece of Corian. It looks like that photo.

Would this be a problem for cutting out the sink? If this is doable, what type of power saw and blade would be used?
I want to be one or more steps ahead of whatever contractors
might say they will do.

I would think that it would need to be cut inside the sides of the sink a certain number of inches from the counter top. Also, it would be best to do it on a warm day as cold temperatures seems to play a role in causing Corian to crack. Any suggestions on exactly where to cut the sink?

Good point about getting a top mount sink that will exactly fit. We also plan to get rid of the garbage disposer which we seldom use. That would open up more space underneath the cabinet.
chispa
11 years ago
Has the poorly insulated window been fixed? Have you called a Corian fabricator? They might be able to fix the crack. I would use someone that specializes in Corian and not a "know-a-little-about-everything" renovator.
PRO
Olive Mill
11 years ago
Hello,

Cracks in the sink are usually caused by thermal shock. For example if you pour boiling water into a cold sink, the material expands and a crack can start from the drain opening. This usually happens over time and then when you wipe dirt into the crack you notice it.

If you run cold water while pouring the boiling water, it will lessen the chance of cracking.

The sink can actually be cut out and replaced with a different style or the exact same sink style.

I would contact Back 2 Perfection or Nationwide Surface Repair. They specialize in Corian (solid surface) countertop repair and can do this without issue.

You can also try calling 1-800-4-CORIAN and they can direct you to a certified repair specialist in your area.

If you have the invoice, the sink has a 10 year warranty whereby they will replace at no charge.

Hope this helps,

Andy
Olive Mill

Here is a link that might be useful: Video of how to replace Corian Sink.

(Corrected) Cracked Corian Sink

PeterH2

Comments (8)

PeterH2

Rake4Leaves
Original Author

Related Discussions

friedajune

PeterH2

Rake4Leaves
Original Author

chispa

Olive Mill

COMPANY

BUSINESS SERVICES

GET HELP

CONNECT WITH US

(Corrected) Cracked Corian Sink

PeterH2

Comments (8)

PeterH2

Rake4LeavesOriginal Author

Related Discussions

friedajune

PeterH2

Rake4LeavesOriginal Author

chispa

Olive Mill

COMPANY

BUSINESS SERVICES

GET HELP

CONNECT WITH US

Rake4Leaves
Original Author

Rake4Leaves
Original Author