Washer / dryer outlet not working

14 years ago

I'm a woman and don't know much about this stuff but hopefully maybe someone can help me. My washer would not start last night but the lights on it were working (duet machine). I tried the dryer and it was working (same outlet). This morning I called repair and they said unplug the machine and then replug. I did and for a second it looked like it was going to work and then everything went dead. I tried the dryer and now it won't work. Looks like the outlet died? House is 19 years old. I checked the GFCI (2) and both were good. I went to the breaker box and the switch for that outlet was off and when I tried to turn it on, it went right back off. The lights (2 recessed) work fine in the laundry room. Hoping just a new outlet and if so, a 20 amp?

Featured Answer

bigbird_1

14 years ago

Don't worry, a lot of men don't know much about this stuff either. I'm not familiar with Whirlpool Duet appliances, but if they're like most other appliances the dryer will require it's own separate 30A 120V/240V circuit. The washer and dryer would not be on a shared circuit. Does the dryer have a regular plug like the washer, or does it have a big round plug with 4 prongs on it? The dryer would not normally be on a GFCI circuit if it was 120V/240V.
That being said, you have a short circuit somewhere in the washer circuit. That is indicated by the fact that when you try to reset the breaker in the panel, it immediately trips back to the off position. If you try resetting the breaker again after about a half hour and it still trips off, my suggestion is to call an electrician to troubleshoot the circuit. There could be many places for the fault, starting inside the receptacle, or the panel, or in the appliance itself. Why the dryer would not operate at the same time is a mystery, as it should be on a completely different circuit unless it is 120V only and is a small stackable unit. Either way, call an expert (not an appliance repair person at this point).

Sort by:Oldest

Comments (6)

msgreatdeals
Original Author
14 years ago
Thank you for the quick follow up. Both the gas dryer and washer have been sharing the same outlet for years. The washer is just 2 years old. Dryer has 3 prong like the washer and there is no GFCI there. Actually, I have a GFCI in a bathroom, kitchen and garage. Laundry room is between kitchen and garage. Had 220 added 2 months ago for new oven and some electrical work in the kitchen for remodel but no problems there. Washer/dryer are on own breaker. Going to replace outlet and if that does not do it, guess I will call the electrician.
Related Discussions
remodeling laundry - will FL washer/dryer work?
Q
Comments (1)
All the Front Loader washers that I have seen have a door that opens from the right, with hinges on the left. So a FL washer will fit in your space and the door will open just fine. My FridGEmore set is stacked. On the matching dryer, you can switch the hinges on the door so that it opens from either the right or the left. Usually, the dryer door opens from the left, hinges on the right so that when you put the pair side-by-side (washer left, dryer right) the doors open out from the middle, as it were. Since mine are stacked, I had the installers switch the door hinges on the dryer so the doors both open the same way. If you consider this option, make sure the dryer you purchase will allow you to switch the hinges to the left side. In your space, stacking the washer and dryer (with the dryer door set up to open the same way as the washer door) means that BOTH doors would be able to swing 180 degrees. You may not see stacked units in model homes, but I assure you that there are lots of homes that have the units stacked. (Besides, who cares what they do in model homes? This is your home - do what works for you.) I don't think there's one best way to install the laundry equipment when it comes to side-by-side vs. stacked. It's more a matter of personal preference and how you want to use the space. My personal experience has been that loading and unloading the washer is not a big issue: I put clothes in, I take them out and move them up to the open dryer. I like having the dryer at eye level. I tend to take clothes out of the dryer and hang them up right away. I may take some items out early, I may take some items out slightly damp, etc. Being able to do all my dryer unloading "fiddling" without bending over is very convenient. CMC
...See More
What is ideal location for electrical outlets for washer & dryer?
Q
Comments (3)
There is no universally optimal location since what's optimal for one machine will be inconvenient for another. For instance, I've had 3 different dryers in my house. The initial dryer that was removed when I bought the place had been hard-wired so there was no outlet on the power line. I didn't like that so I had an outlet put on there right where the conduit ended. It was OK for the first dryer I had, super tight for the second, and is perfect for the one I have now, especially since I put the dryer on a platform now to raise it up. Even venting can be problematic. Ideally the fewer turns and bends (elbows) in the vent, the better and the shorter the distance the better. Mine isn't really affected since being in the basement it has to go up and turn to go outside from any dryer I have. But each dryer I've had has had the vent outlet in a different position on the dryer so if I had it against a wall directly venting outside, it would be a problem switching between the dryers I've had. I would agree that convenient access to water shutoffs is definitely a good thing and if I had my choice, I'd use a single lever shutoff that cuts both hot and cold. One lever to flip and you're done. To me the outlets are less critical on placement. I've unplugged my washer once in 30 years and the only times I've unplugged dryers was when I replaced them. One suggestion I'd give is to have some surge protection of some sort on your washer if you have a computer board in there. Could save a costly repair or replacement after a storm
...See More
Is my gas dryer's outlet OK for electric dryer?
Q
Comments (9)
JC, I don't think of it as a downgrade, actually. Like everything else involving my old (1860) house, the answer is complicated. The washer and dryer are presently situated in the basement, a.k.a. the dungeon (dirt floor). I'm thinking at some point it would be better for me not to have to navigate those stairs so often, so we're planning ahead by making the dryer usable on the first floor, where there is no gas line. We had an electric dryer on the first floor many years ago, but the only outlet at that spot looks like an ordinary one. I plug my hair dryer into it all the time. I had a new electrical panel put in four years ago. I remember the electrician asking me about appliances at the time, but I don't know what he did about them, if anything. I'll call him, and hope he remembers (though I don't know why he should). Thanks for your help, everyone. Susan
...See More
Recessed Outlets for Refrigerator and Washer/Dryer
Q
Comments (3)
Dryers typically have right-angle plugs and I've never seen one that when pushed as close to the wall as you're allowed that the plug is a problem with a surface mounted receptacle. Yes, you need room behind the dryer for the vent connection. Read your appliance manual. Dryers typically require at least 1" clearance from the furthest protrusion (and they're not typically flat on the back anyhow), It may require more to connect the vent. Refrigerators typically do require a couple of inches rear clearance. I'm looking at the LG manual I have here and it says 2" rear, 1" top, and 1/8" side clearances. LG does even say "Room to breathe" in the manual like your electrician. You'll also need room for any ice machine/water dispenser hookup. In all the houses I've owned or worked in, I've never seen a recessed fridge or dryer outlet. In fact, it would be a pain because the right angle plugs typically used for these would be hard to plug into a recess.
...See More
bigbird_1
14 years ago
I assumed electric dryer. Sorry. What you can do yourself then is to make sure the breaker is off and remove the duplex receptacle that both the washer and dryer plug in to. Look for a black or red wire that may be loose and touching the electrical box or another wire. A black or red wire normally goes to a brass colored screw connected to the short slot of the receptacle, and a white wire normally goes to the silver colored screw connected to the longer slot of the receptacle.
hendricus
14 years ago
Before you replace the outlet;

1. remove both washer and dryer plugs from the outlet and turn the breaker back on. If it trips the outlet/line has a problem.

2. If the outlet stays on plug ONE of the machines in. If it trips that is the problem, if not

3. Unplug the one machine and plug the other in and repeat above steps.

4. Now you should be able to tell where the problem is.
jake2007
14 years ago
hendricus has it almost right...

You may have a problem with one of the appliances. You want to be sure that if the circuit works with nothing plugged in, that you want to turn off the power first before you plug in and test the washer and dryer individually.

Then you can switch on the breaker to see if it trips the breaker.

The point being is that if there is a short in the appliance, it may spark at the plug when you plug it in if the outlet is powered.
lee676
14 years ago
I've seen this alot recently in the last few years. Code requires separate circuits for washers and dryers, but several older homes have just one outlet back there that serviced an old-style top-load washer (which relied on an external hot water tank for warm or hot water) and a gas dryer, which used 120V/15A power to spin the drum, blow the fan, and run the electronics. Both of these worked fine sharing a single circuit.

But now, people are buying internally-heated front-load washers that draw in a small amount of water (usually cold water no matter how the controls are set, since it's long cooled down in the residual pipes leading from the water heater tank). Then the internal water heater kicks in adding 1000 to 1300 watts to the load, plus whatever the washer needs to run the motor. Run a dryer off the same outlet at the same time, and the circuit overloads.

I'd bet if the washer were set to tap-cold-water-only, with all the quick-speed, delecate fabrics, and low-soil options selected (so as not to have it turn on the heater), the washer and dryer would continue to coexist in peace on the same circuit. Doing this would hobble the washer's capabilities though, so a separate, dedicated 120V/20A line should still be installed for the washer.

Washer / dryer outlet not working

bigbird_1

Comments (6)

msgreatdeals
Original Author

Related Discussions

bigbird_1

hendricus

jake2007

lee676

COMPANY

BUSINESS SERVICES

GET HELP

CONNECT WITH US

Washer / dryer outlet not working

bigbird_1

Comments (6)

msgreatdealsOriginal Author

Related Discussions

bigbird_1

hendricus

jake2007

lee676

COMPANY

BUSINESS SERVICES

GET HELP

CONNECT WITH US

msgreatdeals
Original Author