skip to main content

Countertop help, 2cm edge can it be built to a 4cm?

11 years ago

Countertop needs help! I just bought a house and the builder installed a 3/4'' edge instead of a 1.5" edge, so now the countertop (dupont quartz) looks thin and cheap. Is there anything I can do now after the fact to make it look better or thicker? Can I glue the same material to the bottom of the surface to make it have the illusion of thickness? Or is there anything I can do to convert the 3/4'' edge to a 1/5''edge?

Comments (5)

realism
11 years ago
I don't think it looks thin and cheap. Regardless why don't you take this up with the builder? If they didn't do what you asked then you are entitled to have it corrected.
Tpns28
Original Author
11 years ago
It looks thin on the counter sides since you can see the bottom support. I'm in the process with disputing it with the builder, supposed to close in 2 weeks so I'm looking for options in the event they say no. Still searching if there's any other solutions or tricks I can do to make it look a little thicker. This is how I wanted it to look like, I like the thicker version since it hides the support a little bit and the piece of wood it sits on.

This post was edited by Tpns28 on Fri, Feb 22, 13 at 0:31
Related Discussions
Is 2 cm too thin for a marble double vanity counter top?
Q
Comments (17)
threeapples- I was trying to match existing granite in my kitchen, but the only match was 2cm, which was thinner than the existing countertops. When I told my fabricator that I was concerned about the seam in the middle from a built-up edge, he said: "No problem, we'll cut all the pieces at a 45 degree angle and the seams will be along the edges where you can't see them." Take a look at these photos and see what you think: He even showed me samples where he had done this with highly figured marble, and he just matched the cut pieces at the seam line so it looked like the pattern wrapped over the edge and down the sides as if it were a solid 4cm slab. If you can find a fabricator who has the skill to do this properly, it's amazing, and they can give you whatever perceived thickness you want without obvious seams.
...See More
2 cm countertop without edge buildup - mistake?
Q
Comments (16)
If you know you like the look, then you know you like the look (I do, too). It took me a while to figure out that "I don't think you'll be happy with X" most often means either "I don't like the way it looks personally" or "It's a pain to do it that way." I wish I'd had a translation dictionary at the beginning of each project! (My husband and contractor both thought 3 cm was the way to go and I didn't feel strongly enough to want to use up all my vetoes that day!)
...See More
Considering 2cm Silestone with laminated edge to 4cm
Q
Comments (1)
4cm is a good look. It will look good if done by a competent fabricator, one whom you should choose carefully. You get what you pay for. You can always ask them to produce a small mock up.
...See More
Thickness of 2cm Countertop Underlayment (and Type of Material)
Q
Comments (10)
First, I would question the professionalism of your installer. Underlayment is not the same as industrial grade PB, that being said, MDF or plywood would be a much better choice, and yes, I would use 5/8" material rather than the 1/2". Especially if you have Euro cabinets you will run into problems. Spanning the DW area should not be a problem, just make sure they don't put a joint close to that area. FYI Particle board comes in a number of different densities. This indicates how much wood and how much filler or adhesive is in the sheet. Industrial board is a 45 lb density, commerical board is 42 or less while some underlayment is less than 20 lb density. MDF is typically over 50lb density, and very stable, some are even exterior grade and water resistant. A contractor that buys based on price at a box store, is, in my opinion, not a professional. Good Luck !
...See More
wi-sailorgirl
11 years ago
The counter you're showing in your second picture has a mitered edge I think. (Basically they cut the counter and the edge piece at a 45 degree angle and glue them together). I'm pretty sure it's too late to do that to your counter (it's a pretty complicated thing I think and not all fabricators do it anyway.) it is also a significant up charge so I would never assume that's how it would be done unless discussed specifically in advance.

I am no counter expert, but you may still have the option of adding a piece around the perimeter (depending on the overhang) to thicken it up. You will get a line through the middle though. It shouldn't be as noticeable on quartz as it is on some natural stones but it will still be there. What I don't know is if that's something that can be done after it is installed.

Another option might be to pull back the trim piece a little so it's not so noticeable.

Really you just need to do as suggested above and meet with the builder to find out what can be done. You may be SOL unless you're willing to spring for new counter (and if that's the case maybe you can just get the thicker edge on the island to save money).

By the way, 2cm counters are not at all uncommon and many people (especially in Europe and Australia) actually prefer them. That doesn't matter if you don't like them, but I don't think anyone would walk into your home and think it looks bad.
ci_lantro
11 years ago
FWIW, I really prefer the sleek look of the thinner counter tops. No way do your counters look 'thin & cheap' to my eye!

When I see thick (or thick looking) stone counters, I get awful visions of the floor joists bowing underneath all that weight!

The other thing about the 1.5'' edge is that the thickness reminds me of Formica counters...and I'm not a stone snob by any means. I'll almost surely use plastic laminate for my counters but, all along, I've planned to make them .75-1.0'' thick just because I prefer that look.
PRO
Rachiele Custom Sinks
11 years ago
There is a relatively simple fix. The quartz material can be cut into strips with a profile on it. Those pieces can be attached below the current top, setting the new piece about 1/8" behind the top piece. I did a quick sketch to illustrate what I am suggesting. (Dino Rachiele) If you have further questions, you can email me at Dino@Rachiele.com

Here is a link that might be useful:

Sign Up to Comment

Related Stories

KITCHEN DESIGN Kitchen Details: The Right Edge for Your Countertop

By KitchenLab Interiors

Square, Mitered, Waterfall or Bullnose? See What Counter-Edge Style Looks Best to You

MOST POPULAR 9 Real Ways You Can Help After a House Fire

By Alison Hodgson

Suggestions from someone who lost her home to fire — and experienced the staggering generosity of community

STUDIOS AND WORKSHOPS Your Space Can Help You Get Down to Work. Here's How

By Laura Gaskill

Feed your creativity and reduce distractions with the right work surfaces, the right chair, and a good balance of sights and sounds

Storage Help for Small Bedrooms: Beautiful Built-ins

By Becky Harris

Squeezed for space? Consider built-in cabinets, shelves and niches that hold all you need and look great too

KITCHEN DESIGN Design Dilemma: My Kitchen Needs Help!

By KitchenLab Interiors

See how you can update a kitchen with new countertops, light fixtures, paint and hardware

INDUSTRIAL STYLE 7 Ways to Get a Cool Industrial Edge Anywhere

By Summer Baltzer

Whether you call an old factory or a brand-new build home, these ideas can help you forge a raw industrial vibe

KITCHEN DESIGN Key Measurements to Help You Design Your Kitchen

By Steven Corley Randel, Architect

Get the ideal kitchen setup by understanding spatial relationships, building dimensions and work zones

ARCHITECTURE House-Hunting Help: If You Could Pick Your Home Style ...

By Laura Gaskill

Love an open layout? Steer clear of Victorians. Hate stairs? Sidle up to a ranch. Whatever home you're looking for, this guide can help

SELLING YOUR HOUSE 5 Savvy Fixes to Help Your Home Sell

By Kristie Barnett, The Decorologist

Get the maximum return on your spruce-up dollars by putting your money in the areas buyers care most about

BATHROOM WORKBOOK Standard Fixture Dimensions and Measurements for a Primary Bath

By Steven Corley Randel, Architect

Create a luxe bathroom that functions well with these key measurements and layout tips

Sponsored

More Discussions

Chip in brand new laminate countertop by cabinet installer!

11

Countertop and backsplash suggestions

4

Kitchen Remodel Finally Finished

7

quartzite countertop suggestions

6

Omega cabinet shaker door outside edge profiles

0