Just an update - all that worry, and the treadmill part was so easy I could not believe it. I was a little short of breath when they finished and said I had reached my target heartrate. I was amazed, as I am very out of shape. Clothes did not matter there -The second worst part was having to wear this huge gown, no bra, pretty open in the front for all the wires although they did tape it for me - the armholes were so big you could see every thing anyways. The very worst part was when the technician kept jamming the ultrasound wand under & into my breast before and after the treadmill. I had to brace myself on the table she was pushing it in so hard, I thought she would push me off. Something was really pinching into me when she pushed, Not sure if it was a probe with a wire attached that was being pushed in by the wand or just the tip of the wand. THAT really hurt, almost as bad as the mammo. I had a mammo and the stress test back to back, but it was done quick so I had time to treat myself on my half day off to some shopping, but I got dizzy halfway thru the store so did not buy anything. I must say, This was the very worst (painful) mammo I have ever had too. Also,the blood pressure monitor for the stress test, wow, I have never had anyone cuff me so-o-o-o tightly before(three times!). She said something about the "lower your pressure is the tighter they have to wrap..." or such - never heard that before. No doctors were present when I was there, just the technicians, who were quite nice. Well, wonder when I will see the results. (Last time it took a month to hear from Dr. on my mammo, then another month to get an appt, then another month to get a referral for breast ultrasound, then same for a needle aspiration..)

@maxima9 It is most likely an air pressure switch. That is what the clear tube going into the back of the control panel senses. As the water in the drum fills it creates air pressure in the tube. The other end of the tube goes into the drum and is usually connected to the center agitator which has holes in it. As the water fills the drum the water will fill the clear tube and increase the air pressure. This pressure change is then read by the computer in the control panel. Once the correct pressure is reached for a small, medium or large load then water inlet valve is turned off. It is most likely all computer controlled and not defeatable. I suppose you could cut the tube and insert an tee. Then attach a tube to the bottom of the tee and route it outside your washer somewhere convenient. Then put a gas tight valve on the end of the tube. When you want more water in the drum open the valve to allow air to enter the clear tube and keep the pressure inside the tube low. Once the water level is close to your liking, close the valve and the pressure will then build inside the tube and eventually reach the proper pressure to turn off the water. That procedure above would all be premised on their being no timer on the water fill valve. Many computer controlled valves don't rely JUST on the pressure switch, but rather amount of time the valve has been open as well. This is to prevent a flood. The fill valve has a max GPM rating that can't really be exceeded by increasing pressure. The manufacturer knows what this rating is and programs the computer to close the fill valve before the tub would theoretically overflow. This is usually a safety in case the pressure switch fails. Even if you COULD increase the water level there is no guarantee that the motor is strong enough to properly agitate. If they designed it for 6-10 gallons of water and you can fit 25-30 in it that would mean the motor has to work with 240 instead of around 80lbs, plus the weight of the clothes. You see to be an eco washer also means they can cheap out on parts as well. Smaller motor, less cost, etc. I would not "trash" the washer. Just sell it used on any of the normal online places. Someone will take it. Then don't make the same mistake again.

Just thought I'd add my two cents (or is it 20 now?) to this..I started on a 2% testosterone cream twice daily ten days ago, and will be using it once a day for the next ten days then switching to at .2% after that as prescribed by my compounding pharmacist. He has recently returned from a conference on Libido and said that for many women a "jump start" is necessary for kicking the libido into gear and finally, after four years of lagging sex drive I am beginning to feel the positive effects of the testosterone....with no negative effects...once again proving that we are indeed all different in our metabolism of all types of things, hormones being only one.......Anyway, I thought I would also share that my pharmacist also says that one of the presenters there at his conference said that in twenty years he has never known there to be a failure of increased libido with the use of DHEA cream - the downside for women looking for a solution "now" to an ongoing problem is that it can take three to six months to take effect....hence the "jump start" idea....but perhaps for those of you with problems with testosterone - ask about the DHEA cream.....the best to you all....Patti

dear Window 1: I don't understand your Answer, quite. Could u explain, pls.? & by northeast, do u incl. Ohio? do u mean northeast US? Could u tell us WHY Low e 366 would or does negatively affect passive solar heat gain in cold winter months, & what exactly u mean by that? ie. explain it f/ laymen/women w/out a lot of knowledge yet in this area? TY! @ 1st I thought the low e 366 would be ideal to keep my older home warmer in cold weather, as it gets brrr cold in here bc of lack of insulation in the walls, so thought this 366 would definitely help! (w/ a new full view storm/screen door, which I need anyway.) Thnks!!!