Okaaaayyyy...... If I run HDMI, I would also want the Cat5 for the IR (since the TVs would be on different levels of the house). If I did HDMI over Cat6, I'd probably also need another line for IR in that case too, plus expensive "converters". Does (can) the Cat 5 run along with the HDMI cable? Where would you have them located in relation to each other? If I use HDMI for the main HDTV where the cable box/DVR will be located, I can't then use the component output at all for other TVs--I would have to split and use HDMI, right? It's one or the other signal? Thanks! I'm meeting the LV guy at the house tomorrow to mark what I want and where. Maybe a few more questions: I think we'll use TWC telephone, but I only see the need for 1 actual phone location, the rest will be "satellites" of this. This will be Cat5, right--and you just plug the plug the phone into it? If there are other Cat5s run for computer, do we need to differentiate these (from that used as phone line)? Anything else I need to keep in mind, or consider, or ask of the LV guy??? Thank you all for your help! Tracey

Definetly a signal strength problem. In my area the cable co. only gives out HD boxes with a technician visit as they must measure the signal strength at your house to ensure proper service. The meter they use cost's a couple thousand dollars and gives a meausuremnt of the bandwith you are able to receive. (I know this because the installer at my house accidently forgot and left the meter in my basement, he was a nervous wreck when he came back looking for it later that day). You signal problem could be a result of too many splits or poor wiring inside the house or just plain poor signal coming into your house. Things to look for are where and how many splitters are you using? If possible you want the HD box and cable modems to get the top priority. For example in my setup the incoming signal is split three ways one goes to HD box one to cable modem and one feeds a 6 way spiltter for the rest of the house. You need a higher quality RG6 cable if you house is wired with RG59 or low quality RG6 you may not be capable of passing enough bandwith for the HD box. And finally your HD box should have a setup screen that shows the incoming signal strength, talk to a technician and see if they can guide you through checking this out over the phone might be helpful.

"Are you sure all these receptacles are not chained off the first GFCI? If you push the test button on the GFCI do the other receptacles stop working? " Positive. They're on totally separate circuits, for one thing. If testing the GFCI on one circuit causes outlets on totally different circuits to stop working, there is a big, big problem somewhere. "There's nothing wrong with all the bathroom receptacles on a single circuit with one GFCI as long as there's nothing else on that circuit. " No, but it is weird. I've not seen that before, ever. However I am unused to some of the shoddy things I've seen in newer tract housing. That's as opposed to some of the things I've seen in much older homes - such as wiring so old that it was still legal when the wiring was put in to have in-line fuses. My guess is that wiring it this way was a way to save money on having to put in another GFCI for the 2nd bathroom. Not putting one on the washing machine outlet was just sheer incompetence. But its still shoddy because now if someone in each bathroom switches on a hair dryer, you risk overloading that circuit. A hair dryer can draw 12.5A - and 2 of them on the same 15A circuit (and lets hope Dad isn't shaving at the other sink at the same time - or, come to think of it, running his OWN hair dryer, in this day of equal opportunity primping) is not something you want to do on a regular basis. "There's nothing wrong with the refrigerator being shared with a dining room receptacle if it is a 20A circuit (and it feeds nothing other than receptacles in the kitchen and dining room and like areas). " There most certainly is. There are power spikes on lines running something with a motor like a refrigerator. Plug your computer into a line on the same circuit as the refrigerator, and see how far you get. (Well, actually, the microwave would be worse, but it still wouldn't be that great). It's not even in the same room - there would be no reason for anyone to suspect that that outlet is not on the same circuit as all the other outlets in the room. This is not an attached dining "area". It is a totally separate room that is listed on the floor plans as "home office/formal dining". The dining "area" is on the other side of the kitchen, congruent with the living room. I doubt that you can lump THREE areas - kitchen, "dining area", and a "dual-use" office/formal dining room all into one under building codes. Also, it is a 15A circuit. Given that there is an outlet in the hallway that is closer to it than is the line for the fridge, I fail to see any advantage to hooking that one circuit in to the kitchen, fridge or no fridge. For all I know - I haven't checked yet - the microwave could be on the same circuit. I kind of doubt it, but at this point I have no idea what circuit the microwave is on (its built in) which raises the potential for problems should I find out the hard way that my Vita-mix is on the same circuit as the microwave. If for no other reason than I end up having to run out in the snow and switch the breaker back. The microwave also ought to be on a dedicated circuit - but it clearly is not. My guess is that it is on the same circuit as the rest of the outlets on that side of the room, which puts anything you have plugged into those other outlets at risk when the microwave comes on. And before you scoff at the idea of a dedicated circuit for the microwave - a 1200W microwave draws 10A to 11A (depending on how close your supply voltage is to 120V). It should be on a 15A circuit to account for the spike it causes when it comes on. That leaves little or no room for other things on the same circuit. Some fluorescent lighting - probably OK. Other high-draw appliances, such as food processors or powerful blenders or mixers - not OK. The microwave should be on its own circuit. Oh, and here's another Really Stupid Way To Wire Your House - the hall lights are on a 3 way switch. There is a switch over by the living room. A switch outside the doors to the Master bedroom and the bedroom next to it. And the 3rd switch is outside the bathroom door. Which means the 3rd bedroom has no switch within reach. Which means when you get up in the middle of the night, you either risk breaking your neck getting to the bathroom, or you take a flashlight with you. Having a switch next to the bathroom, and none within reach of the 3rd bedroom, is sheer stupidity. Outside of TV shows about teenage cyborgs, nobody sleeps in the bathroom. And if you did - you wouldn't need access to the hall lights to get there. "Prewiring for an electric cooktop even when a gas is installed is quite commonly done for practical reasons" Well yes, it is. I mentioned it because I see the breaker in the box, but I can't see the outlet for it. I ASSUME it is wired to an outlet behind the current gas stove, but I have no way to test or check that without removing the stove, which I am not about to do. Another weirdness is where they mounted the breaker box. The breaker box is mounted on the OUTSIDE WALL of the garage, IN FRONT of the backyard fence to boot. It has to be locked - which is actually no protection from meddling because the only kind of lock you can put on it (because the place for it will only accept a small hasp) is easily snipped off. There is just no reason that couldn't have been mounted inside the garage or elsewhere inside the house. In addition, having to lock the box (and then having to keep track of the keys for it) means an extra thing you have to fiddle around with in the cold/dark/snow/rain/ice or whatever. I'm no spring chicken any more and I don't relish having to find the keys (possibly in the dark) go outside and fiddle with my breaker box in the rain (which raises potential safety issues on top of everything else) because my VitaMix blew the circuit breaker when my housemate unknowingly turns on the microwave at the same time. Or whatever other circuit gets unknowingly overloaded because things are not as they should be. Which is why I always map the breakers in a new place - hence this recent exercise. "There's absolutely no requirement that each bedroom be on it's own circuit, and in fact, many designs specifically don't do that. " If there isn't, there ought to be. Now instead of having 15A for each bedroom, the 2 rooms have to share 15A. It is bad design, whether or not "many designs specifically don't do that", especially in the era of a computer and TV in practically every room. Keep in mind, its not just the lights or just the outlets that are all on the same circuit - it is ALL the lights AND outlets in both rooms. In the meantime, there is a 15A circuit in the laundry that has only that one outlet on it (and maybe the lights in there, I forgot to write that down). Then there is ANOTHER outlet on the other side of that room that is on the same circuit as some of the garage outlets. And no real use for either outlet as the room is way too small to try to iron in there, not to mention how inaccessible the one behind the dryer is anyway. I'm sure its not against code. It's just against common sense. "Frankly other than the fact your panel is mislabeled, nothing seems out of code or even contrary to normal practice. " The only thing I said was against code - except possibly the refrigerator situation, which, if it isn't against code, certainly OUGHT to be - is the fact that the outlet the washing machine is plugged in to is not GFCI. Frankly, if you think that isn't against code, I hope you're not a professional electrician - or an amateur one either, for that matter. The rest of it is just sheer stupid design, and - as I said - I strongly doubt the inspection for this place was done properly, looking at the situation in the "laundry room" with the washing machine plugged in to a dedicated circuit (good) but without GFCI (bad). There was another thread where people were jumping all over a guy who was trying to get a layout from his electrical contractor, because some folks felt that the consumer/customer has NO RIGHT to have things done his/her way. This sort of stupidity is EXACTLY why anybody with any common sense gets a layout before allowing the electrician (or plumber, or the guy who is going to put in the interior walls, or anything else) to go to work. Otherwise you end up with all sorts of stupidity - like a shortfall of amperage in 2 of the bedrooms, one of which is supposed, after all, to be the MASTER bedroom, and outlets in a room the size of a closet that will never ever be used. And fridges on a circuit that feeds an outlet in a totally separate room, and god knows where the microwave is drawing power. And the panel being improperly labeled at the time of installation, by the guy who actually did the wiring, IS a big deal. That's just another indicator of shoddy work. The information should have been on the plans - and if the plans were not followed, then that's yet another sign of crappy work.

I think what you're looking for is a matrix switch. a 4x4 matrix switch will allow you to connect 4 video sources to 4 TVs and watch them in any combination imaginable, ie source 1 on tv 1 and 2 while source 2 is on tv 3, or source 1 on all 4 tvs or each source to a different tv, etc. They can be purchased in various configurations, 1X4, 2X4, 2X2, 4X16, etc...I'm guessing you'd be looking at something like a 4X6 (4inputs to 6displays). you could also hook up a computers, ps4, dvd, etc . Keep in mind that all of your video sources would be centralized, so remote control will need to be thought out. Different models will can transmit video signals via HDMI and even ethernet. unfortunately, the price tag can climb quite quickly, so this solution might not be for everybody.