Gotta say I'm more than happy with my 36" RNB. I have been using it for just about a year now and have not had 1 issue. I did break the thermostat for the griddle while installing the hi-back guard and shelf but it was replaced very quickly, my fault. I replaced it too, no need for a service guy w/these machines, I adjusted all my burners too, easy. I also have a 30" Wolf convection and a Wolf steam oven but do use the BS oven for pizza, big hunks of meat and anything I want to use a big sheet pan for. The BS oven is the quietest when using convection mode and I love the ability to turn the fan off w/a switch, the Wolf fan stays on for quite some time after the oven is off and is LOUD. The steam oven fan is also relatively loud, we use that oven the most of any of them. I would absolutely purchase another BS range. I hadn't even heard of them until I was starting my new construction and ended up on this site. I read all the horror stories but with all the stellar reviews I figured I'd take a chance. Got a moss green range and matching pro-line 1200 cfm hood (talk about loud). Initially I was interested in the AR performer, the place I purchase from had Capital, AR and BS all right next to each other (didn't even consider a Wolf). I had looked at an AR at another place by itself but when I saw it next to the BS I didn't even look at it again. I may have been equally happy w/the AR but am very happy with my BS. Really the only thing I was remotely concerned about was the hot door as I have young twins (5 now, 4 when we moved in). When I saw my boy sitting on the floor in front of the range with his back against the door while it was on my worries were over, he was 'warming up'. Heck my Wolf lower panel gets hot enough to be quite unpleasant when it's on which surprised me as no one has ever complained about that. Having the 'known good' Wolf in the same kitchen as the BS oven I can say they've both been brilliant. However it does make the Wolf seem 'not soo special' since the BS is equally 'special'. I do most of my bread baking in the BS just cause I can fit more in there but have used all 3 (steam oven only goes up to 445 deg though), they all work great but the end product is slightly different in each which is kinda cool.

It just seems from what I've read here, there is a lot more trouble with the ovens in American ranges. It seems that the service can be more of a gamble too. If you search American Performer, you can read more. It is the closest in function to the RNB. It has star shaped uncapped burners like the RNB but with a semi sealed burner tray. It might be ok for a range top but I would not want the range. American also has ranges with capped and sealed burners and lower BTUs. Their DF has sealed and capped burners and a fairly simple oven, single fan, with only a standard bake and a true convection mode. There is very little in the manual so I would want to really see how it worked before I bought. If you don't have confidence in a local dealer for BS, consider buying from Trevor Lawson at Eurostoves. He takes excellent care of his customers and has helped some on this forum who did not buy from him.

What is a "local safety officer"? What do you mean "a bunch of back and forth" with your "local safety officer and Wolf"? What prompted you to use your CO meter to test the levels? They are employed by our BC safety Authority who are the regulators for all regulated work, gas and electrical and such. As a licensed gas fitter I hold my ticket through them and they are the final say when it comes to appliance safety. Permits and approvals for equipment go through them. I chatted at length with him about the stove and he did agree we can’t do anything because it meets ANSI standards being below 800ppm, but he did say he wouldn’t have it in his house. His advice to me was if Wolf won’t do anything to then adjust the burner input by under firing the appliance to bring the CO back inline. I went to Wolf with this information and they said ‘based on your requirements I don’t think Wolf products will be right for you, would you consider a buy back’. Checking CO is very common here in Canada especially when commissioning an appliance. I didn’t mention the CO alarm going off because it never went off, however it did show peak levels in the 15-19ppm range after cooking for a short period of time. Enough to make me concerned with a pregnant wife and 2 yr old. This is what will happen if you in a room where the CO levels are 800 ppm. The ANSI standards are referring to the CO levels in the air coming out of the range vent. 800 ppm air coming out of the vent does not translate to a room concentration of 800 ppm. Especially if you have your ventilation on. Now, if you were getting 250-300 ppm where the cook was standing, that indicates a concentration of way more than 800 ppm out of the vent, and thus a violation of ANSI standards. Either way, those readings were way too high and Wolf's response was poor. Yes, I agree, somewhat. The stove should never be operating at the ANSI levels, your house would build up to a dangerous level of CO over time ie. When cooking a turkey for hours. Our utility will actually shut down any gas range over 540ppm during normal operation. Also they shutdown any other appliance if its over 250ppm while operating. I agree we need ANSI standards but as new homes get built tighter and with less makeup air having a cooking appliance pumping 800ppm at the vent/flue is insane. Consider this regulation was put in place in 1926, buildings have changed considerably since then. So, what happened when you tried adjusting it? Was 250-300 ppm the lowest it would go? That would surprise me, I have adjusted several gas ranges and have usually been able to get them down to 30-40 ppm from as high as 500 ppm. I knew this question would pop up, but yes I went through the full range of what is reasonable on a brand new appliance. Below is what I went through, to try and reduce the CO: Tested inlet pressure, adjusted within 1”wc of manifold pressure. ‘Wolf recommends having inlet pressure within 1” for proper operation’ – no change Checked flip top regulator and it was set to natural gas Checked manifold pressure on stove it was at 5”wc Verified orifice was correct as per spec sheet supplied by Wolf Adjusted air shutter, no change was actually higher and this was the lowest I was able to get the stove to run at CO tests were done after 10-15 minutes of operation and the burners were warm Clocked meter to verify burner input is correct Verified no blockage in burner tube Verified all secondary air ports were free and clear House is still very drafty, so not a lack of air within the house The only thing I never did was under fire it, as I didn't want to go down that road on a brand new piece of equipment. Wolf blew me away with their service and willingness to make a customer happy. From a cooking standpoint however, it will be Bluestar for us.

A traditional wok burner is a jet aimed dead center in the bottom of the wok that created levels or heat with the most intense being in the center. Since the burner on the Bluestar is round, it creates a ring which you can clearly see in the photo as I was seasoning that wok. This ring which may not seem like a big deal is about the exact size of the amount of oil, ginger and garlic that most recipes start with. It is not a huge issue and it still works great once you get more food in the wok. The griddle is built in, it is one lone burner underneath and is temperature controlled. All the Bluestars can take the Interchangeable Griddle Charbroiler accessory There is some movement when I cook in the wok but not a ton. You can really move the food around easy since it is so large. I have the 36" so that picture is it in the front right, the center is the griddle and 2 more burners on the left. I do not think I use anywhere close to the 22k when I use the wok. Anything past medium and the flames are wrapping up the sides.