2000 Sunfire Spark Plug Removal

18 years ago

Just jumped over from the computer forum to seek some advice.

One of my adult children just bought a 2000 Pontiac Sunfire 2.4L with 111,000 miles. All in all the car is in pretty good shape. My concern is that it is apparent the spark plugs have never been changed. I have changed spark plugs my whole life and am not overly afraid of this task except it has an aluminum head. Is this a time when I should allow a professional to handle it? If not would this protocol be sufficient:

1.) WD40 and allow to set.

2.) Take out in a continuing in and out motion until fully withdrawn

3.) Use of anti-seize

Would torquing be necessary?

Open to any and all suggestions.

Sort by:Oldest

Comments (7)

gary__
18 years ago
1.) **WD40 and allow to set.** IMO, no value to doing this.

2.) **Take out in a continuing in and out motion until fully withdrawn** Not a bad idea if they come out a little hard. Probably won't be an issue.

3.) **Use of anti-seize** Absolutely.

**Would torquing be necessary?** It's a good idea if you can get a torque wrench on them. Even one would help get a feel for how tight is right for the others.

****

Just changed the plugs on my 20 year old car last summer. I too was a little apprehensive because it has aluminum heads. Didn't have any problems. Just be careful when installing the new plugs. That's when you're most likely to goof up the threads either by cross threading to start with or over torquing. Assuming this car has the usual ignition system, might as well replace the plug wires too while you're at it and maybe the cap and rotor. Often times one or more wires get wrecked while pulling them off the plugs, and they're getting old anyway. jmo
kalining
18 years ago
Why does everyone freek out when they see aluminum heads ?
Just pull out the plugs. Don't even think of pouring wd40
down there. That stuff is a drying agent. when it splashed down to the plug threads, and it will, you will
have problems getting the next set of plugs out. Anti seize
is good if you want to leave the plugs in there for the next 3 years. I think this car has crank fire so no distributor. Changing the wires is a good idea. Plugs don't
go in any tighter in an aluminum head that a iron head.
Just a thought. If this engine has never had the plugs
changed WD40 might be the best idea and do it when the engine is hot. good luck.
Related Discussions
toro ccr2000 ignition problems
Q
Comments (5)
I believe it is a spark problem, since testing today I tested for spark, without the carb or fuel tank. The results were the same. With a new spark plug grounded, a strong spark. Then with the spark plug torqued, no spark at all. All switch wires disconnected, and contact points cleaned. Prior to testing I checked primary lead and coil grounds using an ohmeter. The snowblower is a Toro CCR 2000E, model 38186, S/N 2000151 . Prior to the last tests, I did clean the carb using a commercial carb cleaner bath. Although as stated, the last test was without the carb installed. My next course of action was to disassemble crankcase, first removing flywheel checking for a partial sheared flywheel key. Nothing wrong with key found. If nothing else this will provide the opportunity to thoroughly decarbon.
...See More
Engine will not turn over without spark plugs r
Q
Comments (2)
Sorry, I made a duplicate post. Please post replies to: http://forums2.gardenweb.com/forums/load/tractor/msg041923456941.html?16703
...See More
No spark on rear engine Snapper
Q
Comments (8)
Sit on seat, let right hand drop down, feel starter button on a tin lid. Remove two screws and remove tin lid. Clean out any accumulation of leaves, dirt, mouse nests, clean contacts on starter button. If mower has been stored, check the engine shroud. Remove it, and check for mouse nests under it, and for a chewed off ignition cable to spark plug! How do i know this?? I just went out to start mine, and found exactly what i have described! I have a 1983 Snapper. It sat for a month in my old garage. Went to start it today. Didn't! Checked engine shroud, and found it stuffed with paper, etc. Haven't removed it-tomorrow will be the day!
...See More
Kawasaki FB460V 12.5 hp Won't Start Weak Spark
Q
Comments (30)
Receive all my parts finally, and had a warm day yesterday. After looking at the gasket surface of the head closer, there was no doubt that I had a leaking head gasket. I taped the corners of sheets of sandpaper onto a large piece of glass and smoothed the gasket surface area of the head. Started with 150 grit and worked my way up. This took some time. I was surprised how warped/uneven the gasket surface of the head appeared to be. I checked that old coil again and the readings were still off so I left the new one on the mower. The old one produced a spark, but meter showed bad readings as noted before. Torqued the head to spec and put her all back together. Started on 3rd pull and purrs like a kitten! Note to others that my head gasket was leaking on the bottom, and it was almost impossible to detect without removing the muffler and/or the head. If I had it to do over, I would have, if necessary, removed the muffler and sprayed carb cleaner along entire the gasket surface with the engine running before removing the head. However, I waited too long and couldn't even get the engine started. In my case, it worked out well because the gasket was definately leaking. Do yourselves a favor and check compression in the early stages of repair before throwing parts at one like I did. The low compression reading, along with Tomplum, got me on the right track. Thanks for the good advice. This site is awesome!
...See More
DA_Mccoy
Original Author
18 years ago
I hesitate as I had a negative experience years ago with a Sunbird.

Thanks for your input.

If you ever need assistance for your computer system stop over at the Computer Help Forum. A lot of friendly, informed members there.

DA
johndeere
18 years ago
The main thing with aluminum heads and plug removal.Is let the engine be room temperature before starting.Do not remove when engine is warm.
coolvt
18 years ago
JD, I would think that a warm/hot engine would make the plug removal easier. Wouldn't the aluminum expand when warm? Curious because I have to do a Volvo soon.
gary__
18 years ago
**JD, I would think that a warm/hot engine would make the plug removal easier.**

No No No No NO. Do it with the engine cold.
jordanweed18
16 years ago
yes agree, never remove the plug when the engine is hot. wait for the temperature to subside before pulling it out. i suggest you get the swag plug, very to install and replace.

2000 Sunfire Spark Plug Removal

Comments (7)

gary__

kalining

Related Discussions

DA_Mccoy
Original Author

johndeere

coolvt

gary__

jordanweed18

COMPANY

BUSINESS SERVICES

GET HELP

CONNECT WITH US

2000 Sunfire Spark Plug Removal

Comments (7)

gary__

kalining

Related Discussions

DA_MccoyOriginal Author

johndeere

coolvt

gary__

jordanweed18

COMPANY

BUSINESS SERVICES

GET HELP

CONNECT WITH US

DA_Mccoy
Original Author