I know a few ways to cut a bottle on the cheap and easy, with mixed results... All of them require a heat source. 1. take a glass cutter and score a line around the bottle. take some cotton string, kite string works good if I remember right. soak it in some alcohol. tie it tight around the bottle right next to the score you made. Lay the bottle on its side, propped up so that it has room to burn. Light the string on fire and let it burn out. Dunk te bottle into cold water and it SHOULD crack along the score. 2. head to a hardware store and buy a roll of masons string. wrap a layer or 2 of scotch tape around the bottle where you want it cut. tie one end of the string to a door knob or a nail or something to keep it stable. tie the other end to another stationary object keep a dip of a few inches in the middle of the string, do not make it too tight. wrap the string around the bottle, over the tape, where you want it cut. going slow at first slide the bottle back and forth to wear a path through the tape and act as a guide to keep the string in the right place. begin moving faster and faster and pulling up slightly on the bottle. as sson as the string melts in two or breaks, stick the bottle in an ice cold bath, it should break right along the line traced in the masons string wear mark. 3. with some long THIN wire and a car battery you can cut a bottle. The wire needs to be thin enough to glow red when its made a direct short. wrap it a single time around the bottle where you want it cut. do not let the wire touch itself where it comes full circle. if it touches itself thats the end of the short and it wont work. keep it as close as possible with out actually touching. use a heavy glove like a welders glove to tension the wire pu pulling the bottle. Have another person make the connections to the battery. One end of the wire to each terminal. The wire will glow red in a matter of seconds and heat the bottle along its path. Most times the wire will burn in half because of the direct short. Immediatly dunk the bottle upto the score mark in cold water. I can see an idea in my head for a votage controller, a battery and a spring to keep the wire tight that would allow you to make a bottle cutter with the wire method. Off the top of my head Id think it would run close to 100 dollars though and not be worth it if you were not going to be cutting very many bottles. With all methods use some common sense. heavy leather gloves, a face shield or goggles, long sleeves. basic safe practices. Also while they will all cut a bottle, they will also leave some sharp edgeds, and maybe a lip. You should use some wet sandpaper to take care of this problem. I would attached some metal sand paper to a board, face up, wet it down and move the bottle back and forth across the sand paper to finish off the edges and smooth it out and make it safe to handle with out cutting yourself. When I was a kid we used to cut bottles with a wire hanger and a camp fire. I dont recall exactly how we did it? Im sure we were not the originators of this idea and someone will have a more complete memory of it. I know we wrapped the bottle in the hanger, twisted it tight with some pliers nad if I recall correctly, let it sit in the fire long enough to heat up the hanger to red hot. After that Im not sure how we made it cut through and got the bottle half back out of the fire? too long ago but any excuse is a good excuse to go camping as summer moves upon us. Maybe Ill play with cutting bottles agin over camping trips into the mountains this summer, see if I can gain some old knowledge from ym child hood again.

Well, CRAFTY, what a nice compliment, and CONGRATULATIONS on your show results. That's just fabulous. Don't think I've seen a final picture here, though. W/love to see it. I didn't think I'd ever leave mosaics either, but it happened. TOOMUCH: I'm into mixed media - art journaling, tag making, back into polymer clay occasionally, card making - altered art on canvas - you name it - paper/paint/glue - table work that is easy on the old back problems.

I have kitchen plans for a 24"built in under counter Bev Fridge. I have tripled my appliance allowance and realize subzero probably is a good choice but trying to stay closer to $1,000 with builder price discount. Uline has one that does both and looks nice enough, but the shelves for the water bottles don't roll out for easy access and loading. Will mainly use it for water bottles/flavored water bottles so it needs to be taller than just cans. I also don't want it to be too loud. Prefer the stainless look with the wood edge wine shelf. Any other options out there?

This is the new version of the wine grotto and it’s starting to pop up in remodels and new construction where i live (texas). We’re planning on converting our old dining room built-in china hutch to a wet bar with fridge, bar sink and pretty stemware storage/display. My mother-in-law is a bit taken aback because to her “it‘s just not done” in a formal dining room. She’s going to flip out when we tell her we‘re turning the rest of the dining room into a bar/wine lounge inspired by our favorite hotel.